Recent content by Jaehui

  1. Jaehui

    Gigabyte X299X - Catalina Support

    I'm glad you're doing as I told you. I'm using it very stably. If you do not insert USB other than the external hard drive before booting, there will be no 100% error. However, it is true that booting is slower than other X299 systems. As Dolga said, the bios are still unstable. I think we have...
  2. Jaehui

    Gigabyte X299X - Catalina Support

    I'm always happy when I get your answer. After looking at the guide, I created a unique number for the DROM and entered it into the SSDT after CRC-8 Check-sum. All the other Thunderbolt features, including hotplug, work surprisingly well. However, it does not seem to be able to receive two...
  3. Jaehui

    Gigabyte X299X - Catalina Support

    I have a lot of questions, but I haven't seen you for a long time. I upgraded Thunderbolt firmware to X299X Designare 10G according to the guide. I followed the CaseySJ link and used the firmware for Z390 Designare and the corresponding SSDT.However, Thunderboltport via Displayport for monitors...
  4. Jaehui

    Gigabyte X299X - Catalina Support

    I have a lot of questions, but I haven't seen you for a long time. I upgraded Thunderbolt firmware to X299X Designare 10G according to the guide. I followed the CaseySJ link and used the firmware for Z390 Designare and the corresponding SSDT.However, Thunderboltport via Displayport for monitors...
  5. Jaehui

    [SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

    항상 많은 정보를 제공해 주셔서 감사합니다. 가이드에 따라 Thunderbolt 펌웨어를 X299X Designare 10G로 업그레이드했습니다. 그러나 업그레이드 후 모니터 용 Displayport를 통한 Thunderboltport는 작동하지 않습니다. 나는 이것을 이렇게 연결하여 사용하고 있었다. 그래픽 카드 디스플레이 포트 # 1-> M / B 디스플레이 포트 # 1-> Thunderboltport # 1-> 모니터 Thunderboltport 원래 디스플레이 기능을 확인 했습니까? 그것을 해결할 방법이 있습니까?
  6. Jaehui

    Gigabyte X299X - Catalina Support

    I haven't solved the bios problem of using two OSs yet. It is normally used when certain USB storage is connected. I don't think it's perfect yet.
  7. Jaehui

    Gigabyte X299X - Catalina Support

    Does the OS work in Raid0 mode on the Mac? Are you using two OSs, Windows and Mac? How do I set it up? Could you post the method? What version of BIOS are you currently using?
  8. Jaehui

    Gigabyte X299X - Catalina Support

    Thank you for your reply. I changed the bios from F3c to F2b. As you said, there was no bios error without any bootloader except Mac. And my memory became 3,200Mhz. But after unplugging the power completely, a bios error came in. I have no choice but to use Windows because of my company work. So...
  9. Jaehui

    Gigabyte X299X - Catalina Support

    How about BCM94360NG on the board? Does it work with OOB?
  10. Jaehui

    Gigabyte X299X - Catalina Support

    Thank you for your effort for X299X Designare 10G. It's very difficult for me, but I'm following the guide. Clover is being used for build. After setting the Disable Block side = Enable, it was possible to install, but when booting, it encountered a bios error screen. Go out without saving after...
Back
Top