Recent content by immapc

Still Not Working on my X79. Wish I could use USB3 since I had it working on my Snow Leopard Gigabyte system flawlessly.

Yeah for my CPU 12 Core you need the VoodooTSSync.kext to enable all cores I think, and that SMcpu setting. Here is my copy. Use KextBeast, unzip and put it on the desktop. Be sure to add to smbios.plist <key>SMcputype</key><string>1281</string> You may not need this on your 3820 CPU. But I...

Not sure how you guys are getting things to boot without CPUS=1 initially. And I tried to get this DSDT working even from a fresh install. I get hung up at: MAC Framework Successfully initialized using 16384 buffer headers and 10240 cluster IO buffer headers. At that point I can't even boot...

Ok so I have the UD3 Board and I ported over from my install on a P9X79Pro ASUS board. I had things working ok on the ASUS but I couldn't get audio going there since the chipset isn't supported, so I wanted to try out the X79-UD3. It is actually more stable on the UD3 with my install right out...

Your Drive needs this: Boot with UNIBeast and Select UNIBeast not the HardDrive also make sure you are in SATA-0 it is the White Bottom Connector to the Right enter -v cpus=1 npci=0x2000 PCIRootUID=1 GraphicsEnabler=No (NVidia) or Yes(ATI) only choose No or Yes don't type the other stuff. At...

Ok so I bought a new drive to test, Seagate 3 TB. Brand New OOB formatted Extended Journaled GUID 1 Partition. Attempted to copy from USB3 to USB3 and it hanged. Same problem so it may not be the drive...

I Just bought the Thunderbolt 1TB Rugged USB3 combo drive. On USB3 the drive is Freezing or Stalling during copy and mount and unmount sometimes stall. Disk Utility couldn't eject it once too. I found the Link below from someone with Mac Specs so this looks like it is the controller inside the...

Check your GraphicsEnabler=No for NVidia it may be Yes right now for ATI. npci=0x2000 or 0x3000 also PCIRootUID=0 or 1 You can try these at boot also -v npci=0x2000 PCIRootUID=0 GraphicsEnabler=No -x should get you into safe mode a couple combinations though of the npci and pcirootuid...

Yes CUDA can be done. You need to use the CUDA hack. I don't have specific instructions available but I got mine to work by googling CUDA OSX Adobe, and it gives a pretty good boost in AE and Premiere. @ mkoziel You need to know more of the basics. This is a little more advanced but once you...

Yeah I have the same specs you are looking at P9X79 Pro 670GTX and used EasyBeast. You have to type in a few things on the command line to start up -v cpus=1 npci=0x2000 PCIRootUID=1 GraphicsEnabler=No Use UniBeast onto a USB 8 or 16GB Drive. You have to download from the App Store in Lion or...

I just got a P9X79 Pro working with BIOS ver. 3203 and it says 1.02 hardware version on the mainboard. My hardware is 3930K 3.2Ghz i7 Sandybridge E, NVidia PNY 670GTX, 120GB 520 Intel Cherrywood SSD, ASUS DVD, Corsair Vengeance 32GB 1866 Q4DCh. I downloaded ML from AppleStore. Unibeast to...

GraphicsEnabler=No for 680 and Yes for 5770. I had the same sluggish install on a GA-X79-UD3 but my board was bad, the 3D BIOS would hesitate and have tracers from the mouse movement while refreshing screens. I used npci=0x3000 but it would take a long time to install Mountain Lion. Try...

Make sure you click on System Preferences and click the Sound Icon and then select Internal Speaker after your install of the 887/888b kext

I didn't have any sleep problems with the DS3H. I used the Non-DSDT method but I also use the onboard Intel 4000 Graphics. I only had to install 2 kexts, the Atheros and Sound. Also I am not sure what BIOS revision you are on and I don't know the most stable version and I didn't flash mine as...

If you changed your BIOS then you need to get a Matching DSDT if these don't match you will have problems no matter what. So once you get that squared away then work on the other problems. I am not at my Ivy Bridge computer right now to test HDMI but I would use DVI and it syncs to all...