Recent content by GeorgeJames

Hi Edhawk Reporting again. Well I did delete those two kexts and was able to boot from the thumb drive. Noting resetting the NVRAM on the way. I normally have 3 internal drives (2 SSDs and a platter) all of which can be set as a Clover boot loader. I disconnected all the drives except the...

Hi Edhawk As suggested I am reporting back. Made your suggested amendments ONLY. Set UEFI partition on thumb drive in BIOS Got into the OC screen and reset the NVRAM and it rebooted. Got back to the OC screen with the various MacOS hard drives showing again. Tried all but got the same...

Thanks Pilgrim for your quick, simple and concise answer. I shall presume unless informed otherwise that there is intentionally a space between 44 and 55.

No I hadn’t as didn’t know it existed have now read several times and I am not much the wiser. I have also read the other parts of the guide too. I think though we are at cross-purposes for it is not what fields I should amend, which you clearly stated in post #21, but what numbers I use from...

Edhawk would you please indulge me a couple of more times then feel free to let me sink or swim. I assume getting the various variables I use the existing Clover Config.plist so using both Clover Configuator and ProperTree Serial Number In Clover and ProperTree SMBIOS it is the same; MLB...

To follow up these questions despite being possibly superseded by your OC setup. 1. Again not aware and attach a screen shot of Peripherals/USB Configuration. I believe they are the default settings. 2 & 3. Just purchased a Sandisk Ultra 3.2Gen1 and pugged in all the ports and as before only...

That is so very kind of you Edhawk, to spend the time creating this OC set up for me. Scary or what for me! I shall try to pluck up the courage to do it. Hopefully with even clearing the NVRAM if I stuff it I shall be able to get back to where I am now at least.

Thanks Edhawk 1. Will check tomorrow but unaware of it 2. It says Cruzer Glide 3.0 3. I had thought in the last couple of days it might be faulty and have checked out where I can buy a Sandisk Ultra Shift 3 thumb 4. Wouldn't have a clue - nothing I have intentionally done Is there further...

Thanks UtterDisbelief The reason is when I plug in the USB3 thumb it does not show up as an SS just an HS. So as to reduce to <15 ports I removed the SS ones believing them to be of no use. In all the physical ports I have on my hack both USB2 and USB3 thumb are seen and useable. Glad to get...

Hi Feartech "the guide uses hackintool so not sure what you are trying to say here". Sorry to clarify I understand from many credible help sites that I only need to use Hackintool ----- I apologise, I realised after sending the last post that the questions I was asking were originally asked...

As per post #11 been-there-done-that. Hackintool is supposed to do the same so in danger of being a squeaky wheel I would very grateful if you would answer the questions I asked at post #11.

I have removed USBPort.kext and gone back to USBInjectAll.kext (the 999th time of trying) to see what happens. It is as is eg all designated USB3. No good or bad outcome so far. In hackintool if I press the ‘inject’ icon I get lots of SS ports (which I deleted to create my USBPort.kext). When...

Hi Edhawk Having another look at USBPort.kext and wonder whether you can please clarify my previous questions: Are you saying that all “USB 3” ports although showing as HS should be changed to USB3 in Hackintool? (HS01 – USB3.1 Gen2 and HS05 and HS06 – USB 3.1 Gen 1, on the back panel: and...

Firstly thank you so much for amending the EFI and secondly for your quickness. I initially ran as is but then added the serial number and SmUUID numbers I had had previously. Unfortunately after selecting the boot drive in clover I got the screen shown in attachment. Pressed space bar and got a...

Thanks again. I have two monitors one using the DVI and the other using HDMI. I have tried iMac19,1 but one of the monitors does not work but can't remember which one, so that's why I have stuck to MacPro6,1