SOLVED
Don't be a big dummy! Check your /clover/Kexts/Other folder for Lilu.kext, WhateverGreen.kext, and FakeSMC.kext
Somewhere along the line, in my many re-builds of the Clover installer, I lost the three mandatory kexts and never put them back. Then I proceeded to assume they were in there...
This EFI setup doesn't show any macOS drives at all.
I tested it, then edited the config.plist to not hide the Recovery and PreBoot partitions. Still no dice.
Replaced /Drivers/UEFI/ApfsDriverLoader-64.efi with the ApfsDriverLoader I had previously been using, as well as replacing Aptiomemoryfix...
More data!
Since macOS appears to be doing something while only displaying the cursor, I thought to check the log files in /var/log. So, here's the whole folder. Today (March 27 2020) I booted one time and let it sit for an hour or so. Check that timestamp in whichever log files are relevant...
I don't know if this counts as updating Clover; since I can't boot any version of OS X/MacOS on the target system, I can't run Clover to update the bootloader on my system drive. So, my system drive's EFI partition doesn't have a "Drivers" folder. I could make one using mkdir and cp the...
My EFI folders are a mess, because I didn't update Clover on the system drive before updating (you know, like an idiot). I've been using the EFI shell in Clover to copy kexts into the correct folders. It's a pain, but I'm familiar enough with Terminal to use cp, ls, and cd
Attached are some...
Since we're all stuck inside for a few weeks (thanks, COVID-19), I decided to update my Hackintosh. Yosemite 10.10.5 to Catalina 10.15.3.
I done goofed a couple different times (didn't update Clover on the Yosemite drive before installing Catalina, namely) but I've been muddling through. I also...
This is a strange set of circumstances, so first, some background:
I have a working installation of Yosemite on a Fusion Drive (a 120 GB SSD and 1TB HDD), and a Windows installation (separate 1TB HDD). My bootloader is Chameleon v2.2, I think
I had a problem with OS X (unrelated to hackintosh...
Figured it out, it's actually fairly simple. Cursory explanation below:
Since Chameleon's settings are based on the contents of the org.chameleon.boot.plist file, I needed a way to change them easily before restarting. Rather than trying to edit the file each time I reboot, I made a couple...
I've got an alternative to constantly editing the org.chameleon.boot.plist file: If I just make a copy, alter it, then change the name of the original, Chameleon should read the "altered" copy because it uses the correct filename. So, I could just write a script to change the filenames. Easy enough.
(apologies for any incorrect terminology; it's been a while since I messed with my installation)
tl;dr - is it idiotic to use a script to alter the .plist file on my "Boot OS X" volume so I can restart into any OS, bypassing the need to manually select one at the bootloader?
I dual-boot...
Apparently jetsam is part of a block of iOS code that was brought into Yosemite. It has to do with memory management, as iOS memory is much more limited than on a Mac. The error occurs because it refers to code that doesn't exist in Yosemite (but would in iOS)
Everything I've seen says that you...
I just upgraded to Audioengine P4 passive speakers (from a 10$ yard sale pair).
When I need to, I use my AKAI EIE interface and send all audio through my receiver to my speakers. (The whole rear aspect of my desk is an absolute mess of cables)
I plug my headphones (pictured: Shure 440 and Grado...
Try booting into your Yosemite installation via USB, then open the terminal and type diskutil list
This should list all the drives you have, look for the one you installed Yosemite on. There might be a partition on the disk called "Boot OS X"; mount that by typing diskutil mount diskXsY
where X...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.