Contribute
Register

Recent content by Dajjal

  1. Dajjal

    AMD RX 590 Graphics card

    For those that have the Sapphire in previous page, I'm receiving mine by next week so can you elaborate on ''OOB''? are you using the WEG from the first post or just the latest WEG 1.2.6? Also any thing checked in graphics section of Clover Configurator, etc.? This will be used on a Z77X build...
  2. Dajjal

    Radeon RX 590

    Can those with a 590 confirm that at least 1 HDMI output works ? as this is what I will need to connect to a TV. Below is the card I'm looking at getting Sapphire Radeon Nitro+ RX 590 11289-01-20G Bless
  3. Dajjal

    Apple Introduces New MacBook Air and Mac Mini

    As already been discussed many times over, Apple will always charge a premium so doesn’t really makes sense trying to compare cause at the end of the day it’s about profit and not so much best value... I like the mini and it surely can’t be beat in it’s form factor/looks.They should have kept...
  4. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    I know you're not sitting here obviously, but since you implied that I did NOT try a USB2 stick I though that you were actually here o_O I described in detail rather than being vague to try and give a virtual representation thinking that I would get the same.I know there is a Hub at HP26 as...
  5. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    I did test all ports with both USB2/3 Sticks, So I applied the -uia_ignore_rmcf and redid it twice, same thing, nothing comes up on HP26 so maybe that is due to the particular header on the MB or just the way it is on this board?Since nothing comes up on HP26 and your suggestion is that...
  6. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    I made it simple and removed the SSDT hot patches so that logic would have pointed you towards the only other place it could be that clover supports files being loaded from.Also the pre-boot log clearly shows where it's loading from. If you already believe that it's complete you'll just ignore...
  7. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    Do so don't like so my friend :mrgreen:.See how it feels to get a half reply from you?In my previous post I simply asked based on the info I provided how does the SSDT-UAIC look, did you reply?No, did you need problem files of that, No, yet don't want to go Hunting, again with this hunting, it's...
  8. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    If you look carefully you'll find it in OEM.Will make the change then.
  9. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    Debug attached.I left HP25 as 255 as I'm not sure.
  10. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    OK,Does the SSDT look correct?
  11. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    @RehabMan Tried again so here goes USB LayOut Z77X-UD5H rev.1 MotherBoard Rear IO 4 USB3 Ports (Blue) 2 USB2 Ports (Red) Case 2 Front USB3 Ports connected to USB3 Header on MB 2 Front USB2 Pors connected to USB2 Header on MB Port Identification USB2 2 Front USB2 Ports >...
  12. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    No need to 'Hunt' as I did explain myself before and gave debug files in that post.I'm going to start over since I don't want you 'Hunting' for anything ok cause god forbid you pop a vein. Can you provide a link or summary as I asked before where I can figure this out as changing my SMBIOS may...
  13. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    HP15/16 are 2 USB2 ports that's connected the a MB Header in Front of Case (PR11).HP15 is an IOGEAR Bluetooth Dongle.HP16 is a Logitech USB Receiver for Keyboard Mouse.PR11 hub (HP11->HP18) was not here before I changed to 255 I believe. PR21 are the 2 Rear ports on the MB one of which has a...
  14. Dajjal

    [Guide] Creating a Custom SSDT for USBInjectAll.kext

    I already changed the values to 255 but it still happens.
Top