Recent content by csat

  1. csat

    Catalina no Bluetooth with Fenvi FV-T919. WiFi is working.

    Have you attached your Fenvi to the nearest slot near the GPU? It is important and sometimes we place it to another slot that causes troubles. If you did so please disregard of my comment.
  2. csat

    Catalina and SuperDuper - how to use it?

    Better, SuperDuper Beta 2 fixed some bugs according to their site.
  3. csat

    Catalina no Bluetooth with Fenvi FV-T919. WiFi is working.

    I've downloaded a few KEXTS and placed them to "other" folder, then I migrated from Mojave to Catalina again and both WiFi and Bluetooth worked without issues. == BrcmBluetoothInjector.kext BrcmFirmwareData.kext BrcmFirmwareRepo.kext BrcmNonPatchRAM.kext BrcmPatchRAM2.kext
  4. csat

    Catalina and SuperDuper - how to use it?

    SuperDuper 3.3 Beta 1 has fixed the issue.
  5. csat

    Catalina and SuperDuper - how to use it?

    When I was using Mojave I named my hack SSD as OSX and it was easy to backup it using SuperDuper by choosing From OSX to foobar SSD external attached to an USB port. After upgrade my system to Catalina I've noticed two sources: OSX and OSX-data. Running SuperDuper and choosing OSX as a...
  6. csat

    Catalina no Bluetooth with Fenvi FV-T919. WiFi is working.

    It seems to be very hardware issue considering that a small BT dongle makes Catalina recognizes it. The possible pointed out solution above is very tough to my current knowledge. I tried simply place some kexts to /Library/Extensions but only this didn't solve the problem. Neither my Asus nor...
  7. csat

    Catalina no Bluetooth with Fenvi FV-T919. WiFi is working.

    Hi Hardware I am testing is a GA-Z170X, I7, RX-580. Updated from Mojave into Catalina. I have everything working except bluetooth. It is not recognized. It was working with Mojave. Thanks.
  8. csat

    Clover customization. How to prevent clover searching?

    Very good explained. Thank you. Regards CSAT
  9. csat

    Clover customization. How to prevent clover searching?

    @jaymonkey Thanks a lot for your kind response. Sure I should had read the WiKi b4 asking, my bad sorry. At the first look I was thinking about turn off scanning from Clover configuration but it could harm the booting process. I hope that the WiKi shows some examples on how to create...
  10. csat

    Clover customization. How to prevent clover searching?

    My computer have two SSD M.2. One I have Windows 10 and the other, I have OSX Mojave. When I boot from Mojave it takes long time to prompt me to log in because CLOVER make a searching for everything that is installed. Is there a way to customize Clover in order to speed up its booting process...
  11. csat

    I can't install some programs on Mojave

    I think you should accept the license terms before so go to the vertical bar and scroll it down.
  12. csat

    Cannot connect to Tonymacx86 website

    Have you already tried to use traceroute terminal command to find out where the problem is locate?
  13. csat

    [Solved] How can I speed up booting time

    Fixed. The Debug option was set. Thanks.
  14. csat

    [Solved] How can I speed up booting time

    Hi I am using Mojave 10.14.2 and Clover 4769 installed by the latest Multibeast 11. My motherboard is a GA-Z170X Gaming 5, with 32 GB and RX-580. I am using a SSD M.2 Kingston SA1000 with 480 GB, iMac Model 18.3. When I turn computer on it takes about 20 seconds to call clover. When clover...
  15. csat

    How to setup a new SSD?

    Considering my lack of experience and not knowing the whole process I would tell you for sure that the EFI partition will be there after using SUPER SUPER. You will see that the destination disk EFI will be empty when you mount it and the source disk you will see the original EFI. It is simple...
Top