Recent content by arquicion

I’m afraid to say that Big Navi’s drivers will be only release in some forthcoming Big Sur update. I don’t think those drivers would work in Catalina. Nice build, by the way! Hell of a chop!

Yeah! Good! I have a 1TB WD Blue W550 (very suitable!) NVMe SSD mounted inside a USB 3.2 Gen 2 enclosure which connected to back panel ports runs at 970 MB/s - 940 MB/s read and write. Therefore I think that it may be a failure in the case frontal panel because I guess the only chip is the one...

Thanks for your answer. I’m using some NVMe disks in a NVMe to USB C case that was tested to work at USB 3.2 gen2 speeds in the USB C from the back panel (10gbps). I guess that there’s something related to this case's front panel chip. Have you ever test this this USB C front panel header?

Hi CaseySJ, Finally I got a new case with one frontal USB C port (Azza . Instead of USB 3.2 Gen2 transfer speed I can only get USB 2.0 Gen 1 speed. I am not able to find any proper information about the case’s USB C front port chip. Do you think that this maybe the bottle neck? Cheers

Hi mate. I think I have the same GPU as you, it is a Sapphire Pulse Rx 550 4gb and it was recognize as 0x699F. I tried 0x67FF and 0x67EF the way you say and it does make any changes but the cosmetic name. Should I try with different version of both Lilu and Whatevergreen? Thanks!

Thanks! Had not read that mini-guided. What's "ExtendedBTFeaturesFlags" for, technically?

AirportItlwm-Catalina.kext did not work for me. Just getting some Wifi with itlwm.kext enabled and Heliport. Only way to make it work: Changing this value in the config.plist: Set SecureBootModel to Default to make sure IO80211Family loads properly. And voila! Got this from...

I wonder what would happen to Mac applications in two o three years... Will developers then create two type of Mac apps, one Intel X86 and one arm-based? I remember the original Rosseta Fix, back in the 2006, only last for three or four years... So in 2023 we might have to trash our Macs and...

Then I prefer METAL! CUDA Blef is just breaking down! cheers!

Hi Mate! I found it out! The problem is the GPU (MSI AMD RADEON 5700 XT 8GB OC). I'm using boot arguments agdpmod=pikera, anyways there's something to patch in there... Today I got a RX 580 for my old build, and the installations problems are gone with this GPU! I found this while I attempted...

Hey, thanks for you answer, this is my new setup: Mobo: Gigabyte Z390 Aorus ULTRA CPU: Intel Core i7 9700F RAM: Crucial Ballistic 2x16GB DDr43200 MHZ SSD: 1TB Intel SSD 6 M.2 NMVe GPU: Asus Strog Rix AMD RADEON RX 5700 XT 8GB DDR6. PSU: EVGA 700W Bronze 80plus Just tried many Bios setups and...

Hey Mate! How are you? I get something new about: If I install on el SSD SATA WD within this Setup, It just happens the same as on the NVMe (CLOVER O O C). If I use the SSD SATA from my older setup (where the OS is installed) it works just fine. I cloned this SSD to the NVMe and to the new SSD...

Bu the way I didn't mention the your EFI O C boots a lot faster than my CLOVER! :clap::clap:

Yeah! Im agreed with that. I'm trying to allocate the problem. Thank!

Hi! It is not working for me, same results: The pre-installation round works "fine. But it shuts down in the second round, once the installer is finally loaded/booted. The pre-installation round works "fine. Tried resetting NVRAM, and clearing CMOS... an so many many things. Tried the installer...