Recent content by angydangy

  1. angydangy

    Problems booting

    hello i used this same board on yosemite. i experienced the same and similar problems. after 24 hours of straight messing i found a very simple solution i had overlooked remedy run multibeast from the desktop not the usb .... that is all it was put multibeast onto your desktop and run it...
  2. angydangy

    Quicksilver recycling ;-)

    :thumbup: nice one i appreciate that. thanks i can gauge the rest off of pictures
  3. angydangy

    MDD full ATX (another one

    yep sure can. that was why i used water cooling to dissipate the heat on my sealed case and the pad being adjustable . I suppose if you wanted to you could work it off the cpu fan temp control with a lil trickery :eh: ( i don't fancy messing with that :mrgreen: basically a mini air...
  4. angydangy

    Quicksilver recycling ;-)

    could i be cheeky and ask you for a measurement of your front plastic panel. just the width and height would do it . :D please
  5. angydangy

    Quicksilver recycling ;-)

    heya hows it goin. "Recycling" got my attention :thumbup: clean looking build you got going there.
  6. angydangy

    MDD full ATX (another one

    hey g4 :wave: the motherboards are both dead lol it was indeed the cpu however the second motherboard meet a grizzly end .... long boring story i will not bother you with. Basically had a unlucky run heh never mind Riveted the case back up today with a few extra pieces and took all the paint...
  7. angydangy

    MDD full ATX (another one

    ok!! :lol: it still looked like a g4 even after changing some of the features but i am not satisfied so lets delve deeper into the depraving sabotage of this g4 case where you can see the backside of the case and that hammered line across the bottom that is where i flattened out the original...
  8. angydangy

    Project: Quicksilver G4 PowerMac mod

    after saying that i seen this on google images. front_face.jpg
  9. angydangy

    Custom built Desk with watercooling

    this is great man i am enjoying your thread and i like that you used mdf. It's looking awesome.
  10. angydangy

    MDD full ATX (another one

    did a little bit more messing today made a motherboard tray and played about with ideas for the side panels . i keep fighting with myself over the side as to what will look better . i think i Prefer the side panels off as it gives more solid straight lines. So i am considering flattening off...
  11. angydangy

    MDD full ATX (another one

    i made this HDD cradle/cooler today using only heat sink parts from broken psu. It looks a bit rough here i did not even bother to wipe it down or screw it together properly for the photos :ugeek:borrowed a camera for a while so no more blurry pictures. had some trouble with my mavericks...
  12. angydangy

    Project: Quicksilver G4 PowerMac mod

    that would be so sweet with a lil 7 inch monitor sitting in place of the drive bays
  13. angydangy

    MDD full ATX (another one

    WOOOOOT!!!! the new cpu arrived and IT WAS THE CPU that was faulty after all :mrgreen: back up and running. :lol:feels good to catch a break celebration time
  14. angydangy

    MDD full ATX (another one

    tomorrow the new cpu arrives Hopefully the board and the cpu both work :shh: well i got bored so i made another computer its a very basic little mod that has turned out to be a lot of fun parts. motherboard. msi 7301 / n1996 / cuda cpu . pentium D 2 gig kingston ram DDR2 nvidia 7300gs silent...
  15. angydangy

    Custom built Desk with watercooling

    i cannot see the link given but i imagine it is something along the lines of this i am looking forward to seeing your finished project i have often thought about doing the same thing with a coffe table using a laptop innards and making some spread out cells with a vga signal sender to cut out...
Top