Contribute
Register

[Success] - Asus ROG Strix Z490-E Gaming + i9 10900K + OpenCore

anybody have any issues with usb 2's not working? I have 1 internal usb 2 going to my front ports and they are the only ones that recognise my mouse, keyboard, usb headphones and usb 2 drives. Even when using usbinjectall kext none of the usb 3 ports on the back recognize any of these at all??? I went through the mapping process twice just to be sure but still no usb 2 recognition in the back ports.. Any ideas?
 
anybody have any issues with usb 2's not working? I have 1 internal usb 2 going to my front ports and they are the only ones that recognise my mouse, keyboard, usb headphones and usb 2 drives. Even when using usbinjectall kext none of the usb 3 ports on the back recognize any of these at all??? I went through the mapping process twice just to be sure but still no usb 2 recognition in the back ports.. Any ideas?

Do you have the board mentioned in this thread?

Asus ROG Strix Z490-E Gaming

Your signature says otherwise.
 
No its the asus z490 proart. I tried updating my sig a couple times over the last days but its not saving it for some reason.
 
Do you have the board mentioned in this thread?

Asus ROG Strix Z490-E Gaming

Your signature says otherwise.
No its the asus z490 proart. I tried updating my sig a couple times over the last days but its not saving it for some reason.
 
Here's a build of 0.7.5 with all the latest kexts that was released today:

version.png


kexts.png


Bash:
craig@Craigs-iMac ocvalidate % pwd
/Users/craig/Downloads/OpenCore-0.7.5-RELEASE/Utilities/ocvalidate

craig@Craigs-iMac ocvalidate % ./ocvalidate /Volumes/EFI/EFI/OC/config.plist

Completed validating /Volumes/EFI/EFI/OC/config.plist in 1 ms. No issues found.
 

Attachments

  • EFI 0.7.5.zip
    10.2 MB · Views: 157
Here's a build of 0.7.5 with all the latest kexts that was released today:

View attachment 532925

View attachment 532926

Bash:
craig@Craigs-iMac ocvalidate % pwd
/Users/craig/Downloads/OpenCore-0.7.5-RELEASE/Utilities/ocvalidate

craig@Craigs-iMac ocvalidate % ./ocvalidate /Volumes/EFI/EFI/OC/config.plist

Completed validating /Volumes/EFI/EFI/OC/config.plist in 1 ms. No issues found.

It works 100%, thank you very much for the effort.

Just I lost the rear USB-C port for the Apple Audio USB-C Adapter which I have also with the rear USB-C port as active if I use the iMac201_USBInjectAll_v0.7.5_z490 Kext. On the other side, with this kext the front ports doesn't work with some USB drivers.

Is there a way to have both USB-C as with the iMac201_USBInjectAll_v0.7.5_z490 AND front ports works as with the USBPorts? How can I do that?
 
Last edited:
@hemon and @ac9001 USB port mapping has gotten a lot harder since Big Sur 11.3. Using any version of USBInjectall.kext and XHCIPortLimit quirk with Hackintool will not recognize all of the ports and or configure them properly. I've got a couple of Z590 boards and had to resort to loading Catalina and then used a combination of CorpNewt's USB Mapping tool and Hackintool. Even then all the ports were not correctly identified by type, stuff like the wireless bluetooth card and the LED Lighting controller were shown as USB3 when they should be classified as internal ports. I had to manually change those myself, it was a chore. It may be slightly easier with your respective Z490 boards and you be able to get away using the USB Mapping Tool

 
It works 100%, thank you very much for the effort.

Just I lost the rear USB-C port for the Apple Audio USB-C Adapter which I have also with the rear USB-C port as active if I use the iMac201_USBInjectAll_v0.7.5_z490 Kext. On the other side, with this kext the front ports doesn't work with some USB drivers.

Is there a way to have both USB-C as with the iMac201_USBInjectAll_v0.7.5_z490 AND front ports works as with the USBPorts? How can I do that?

Perhaps you can try using Hackintool to inspect that port both with and without the USBInjectAll loaded. Maybe we need to tweak the properties of the port:

EDIT: Also I'd like to know where your USB-C audio adapter shows up in this list while the kext is loaded. Maybe we need to add a port to the map. (like if it shows up as HS04 or something)


1635860984103.png
 
Back
Top