Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

[CaseySJ]

It has been determined that the bcm943602cs Bluetooth interface affects sleep. I plug it into the HS11 usb interface. It is impossible for me to remove it now. Is there the best of both worlds?

Are you using a Fenvi FV-HB1200 or a combination of two separate devices such as:

• Standalone BCM94360CS module
• Standalone PCIe adapter card for BCM module

 

[cqwenjin]

Are you using a Fenvi FV-HB1200 or a combination of two separate devices such as:

• Standalone BCM94360CS module
• Standalone PCIe adapter card for BCM module

PCIe adapter card for BCM module

 

[CaseySJ]

Yes, the primary EFI partition is in the same physical drive as Big Sur.
The Shared folder doesn't have the EFIClone log file.

Please re-check all parts of Step 13 (in Post 1):

Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

CaseySJ's Comet Lake-S in BeQuiet! Pure Base 500DX: Gigabyte Z490 Vision-D - i5-10400 - UHD 630 - AMD RX 580 (Please do not quote this guide in its entirety. Post a link instead.) (See this post for how to refer to a Guide or Mini-Guide.) Refer to the Z390 Designare thread for answers to a...

www.tonymacx86.com

 

[CaseySJ]

PCIe adapter card for BCM module

Which PCIe slot is it in?

• The short PCIe x1 slot?
• The bottom long slot?

Also run IORegistryExplorer and scroll down to XHC (do not use search bar), then click Bluetooth USB Host Controller as shown below, and check kUSBVendorString on the right side. Does it say Apple Inc.?

 

[FTD0910]

Just got my Vision D/i9 10900k Hackintosh up and running!! Overall this install was VERY smooth following this guide. My Apollo system works great right out of the gate too!

Only issue... my fans seem to rev up and down a lot. CPU temps hanging out like 43C when idle. Maybe I just did a bad job at seating the cooler? hehe

UPDATE: I switched Load Line Calibration from auto to Standard and now the temps are a little more reasonable (low-mid 30s on a hot day). I read that a lot of people feel Gigabyte's "auto" VCore is too much... especially with a hot chip like the 10900k

So where do we make this switch? Is it "CPU Vcore Loadline Calibration" that needs to be changed? There is no toggle option for me in the BIOS. Do you have to type in "Standard"?

 

[CaseySJ]

@CaseySJ Attached is the requested DMAR from MaciASL.

I have Big Sur running smooth on 0.7.4 now with those disabled settings you suggested, except my Thunderbolt card isn't working. Would those two things be related?

Please compress and post the entire OC 0.7.4 EFI folder, but with serial numbers removed from PlatformInfo section of config.plist.

 

[CaseySJ]

So where do we make this switch? Is it "CPU Vcore Loadline Calibration" that needs to be changed? There is no toggle option for me in the BIOS. Do you have to type in "Standard"?

Please refer to Post 1:

 

[cqwenjin]

short PCIe x1 slot

Which PCIe slot is it in?

• The short PCIe x1 slot?
• The bottom long slot?

Also run IORegistryExplorer and scroll down to XHC (do not use search bar), then click Bluetooth USB Host Controller as shown below, and check kUSBVendorString on the right side. Does it say Apple Inc.?
View attachment 530247

short PCIe x1 slot

 

[CaseySJ]

short PCIe x1 slot

Try this simple experiment (may or may not work):

1. Go to System Preferences --> Energy Saver
2. Is Wake for Network Access checked on or off?
   
   
   • If it's on, then turn it off.
   • Now check if Sleep works (Apple Menu --> Sleep)
   • If sleep works, stop. Otherwise continue below.
3. Click Schedule as shown above.
   • Now enable Sleep schedule as shown.
     
     
   • Click OK
   • Now check if Sleep works (Apple Menu --> Sleep)
   • If sleep works, try unchecking the Sleep schedule:
     
     
   • Click OK
   • Now check if Sleep still works (Apple Menu --> Sleep)
   • If sleep works, close the Energy Saver preferences box. Sleep should be okay now.

 

[leekh3]

Hello @CaseySJ

I have a question. There is no available gigabyte vision D in US market now, unfortunately. I got a vision G Z490 and bought GC titan bridge separately.

It Looks like your “Modifications for Z490 Vision G” assumes that tb3 is not used.
However, I have GC titan bridge. In this case, what should I do to use GC titan bridge? Can I just skip “Modifications for Z490 Vision G”? Thank you for your time