Contribute
Register

Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

That's out of me. But I was suspecting that the ALC is somehow behaving wrong.
I'm sure you might have researched, but did you find any clue or related issues with the same device?
For now I'm waiting for the updated KX audio driver. If it won't help, I have some ideas about sections I removed from config.plist. Maybe the issue is that driver is working, but for proper sound setup for the each macOS subsystem the sections I removed are actually needed, but the device id should be adjusted.

Audigy RX supports AC97 codec (for example its Linux driver refers to AC97). As I've understood KX audio driver spoofs SB as AC97 device. So I'll try to restore Audio section and set its PCIID instead of onboard audio id. Maybe also I would need to restore the DeviceProperties/Add section, too, and change id (and probably choose different layout id which corresponds to AC97).
 
...
I am using no USB SSDT, my point was to gain BT access. But I think my approach is wrong.
...
Please use the EFI folder provided in this thread (post 1). The USB SSDT is necessary.
 
Hello CaseySJ,
Wanna thanks in advance for this tutorial, this is the only I had success, so thanks!!!!

And I wanna make a little contribution to your great work.

FOR UAD USERS with Titan Ridge 1.0 and have VISION "G" like I do.

After plug my Titan Ridge 1.0 on the motherboard, all TB menus on BIOS just appears because of the connection with THB_C1, so...just followed the configs of the tutorial, and after a reboot, "Voilá" I have 3 Sattelites OCTO and a Twin Quad in daisy chain working like a charm.

Gigabyte compatibility chart says that Titan Ridge 1.0 is not compatible with Vision G, only Titan Ridge 2.0 is, BUT I have tested and 1.0 is compatible as well. (If you wanna buy 2.0 its ok, I will keep my 1.0 for while ^^)

SO I have my Hackintosh fully funtional for audio now with UAD.

Have fun everyone.
 
Hello CaseySJ,
Wanna thanks in advance for this tutorial, this is the only I had success, so thanks!!!!

And I wanna make a little contribution to your great work.

FOR UAD USERS with Titan Ridge 1.0 and have VISION "G" like I do.

After plug my Titan Ridge 1.0 on the motherboard, all TB menus on BIOS just appears because of the connection with THB_C1, so...just followed the configs of the tutorial, and after a reboot, "Voilá" I have 3 Sattelites OCTO and a Twin Quad in daisy chain working like a charm.

Gigabyte compatibility chart says that Titan Ridge 1.0 is not compatible with Vision G, only Titan Ridge 2.0 is, BUT I have tested and 1.0 is compatible as well. (If you wanna buy 2.0 its ok, I will keep my 1.0 for while ^^)

SO I have my Hackintosh fully funtional for audio now with UAD.

Have fun everyone.
Just to clarify a few things... What TB connections do you have on your UAD stuff? Any UAD with TB-1? The Titan Ridge 1.0 is a DSL7540 and the onboard I have on the Z490 Vision D is the JHL7540. As reported not too many TB-1 devices connect to my onboard ports. I had to buy a used Apollo Duo with the TB-3 option card to get my quad running. (UAD is outta stock on TB cards till late July or August) Although I have my Apollo QUAD and Satellite Quad working I still have to figure out why when I change Logic X into 96khz the audio glitches like mad! Tried the old swap audio devices back and forth in the Logic X Audio menu, that doesn't work. It does seem solid at 48Khz though.

If it was easy, everyone would do it!
 
Last edited:
@CaseySJ Regarding my 6800 XT not displaying any video signal between boot up and macos being loaded, I connected my 6800 XT to the monitor via a DP to HDMI cable. DP connected on the 6800 XT and HDMI on the monitor. With this configuration, I have a video signal during post. But DP to DP no signal during post. I updated the BIOS to F20 and it is the same issue; video signal all the way if I use DP to HDMI cable but no video signal until macos loads if I use DP to DP cable. I am starting to thing something might be wrong with my monitor and this card. The monitor is a bit old and only compatible to DP V1.2 whereas the 6800 XT is DP V1.4a (although I would assume backward compatibility).
 
Just to clarify a few things... What TB connections do you have on your UAD stuff? Any UAD with TB-1? The Titan Ridge 1.0 is a DSL7540 and the onboard I have on the Z490 Vision D is the JHL7540. As reported not too many TB-1 devices connect to my onboard ports. I had to buy a used Apollo Duo with the TB-3 option card to get my quad running. (UAD is outta stock on TB cards till late July or August) Although I have my Apollo QUAD and Satellite Quad working I still have to figure out why when I change Logic X into 96khz the audio glitches like mad! Tried the old swap audio devices back and forth in the Logic X Audio menu, that doesn't work. It does seem solid at 48Khz though.

If it was easy, everyone would do it!
Hello supaMac, all my UAD are TB-2!
I just use an adapter on Titan Ridge from TB3 to TB2 to make them work

**** Startech Adapter****

Hope it helps!

I just couldnt make the hotplug to work, not a big problem but should be good to have it working.

Maybe @CaseySJ have a tip to turn hot plug on!
 
I've been running this build for a bit but every so often I get a grey screen (nothing freezes as i can still hear audio but I can't quit anything and have to restart the computer. when it boots up next it either is incredibly slow or gets hung up on the same line in verbose.

Computer stays in Insomnia mode (not sure if that's causing the issue)

My hardware:
Opencore: 6.9
OS: Bigsur 11.3
MOBO: Gigabyte z490 Vision D
CPU: intel 10700k
GPU: Sapphire nitro RX580
RAM: CORSAIR VENGEANCE RGB 2 x 16GB DDR4 3200MHz CL16 DIMM
NVME 1: MacOS - WDBlack SN750 500GB
NVME 2: Windows - WD blue SN550 250GB
SSD 3: Mac Storage - Samsung 860 Evo 2.5” 1TB
 

Attachments

  • 1.jpg
    1.jpg
    1,009.9 KB · Views: 47
  • 2.jpg
    2.jpg
    1.3 MB · Views: 43
  • 3.jpg
    3.jpg
    1.2 MB · Views: 49
OK,
TB3 hot plug works very nice, just tested, here is what I did:

If you are a Vision "G" user like me, just turn on/activate SSDT-TB3HP.aml and SSDT-DTPG.aml from ACPI section and reboot.

@CaseySJ said on his tutorial to turn off or remove those 2 SSDTS because Vision "G" has no thunderbolt on it, 100% true, but if you have a Titan Ridge Rev1 or Rev2, just let them on/active and you got TB3 working on your system with hot plug, cool huh?

I think it may help another people as well.
 
I've been running this build for a bit but every so often I get a grey screen (nothing freezes as i can still hear audio but I can't quit anything and have to restart the computer. when it boots up next it either is incredibly slow or gets hung up on the same line in verbose.

Computer stays in Insomnia mode (not sure if that's causing the issue)

My hardware:
Opencore: 6.9
OS: Bigsur 11.3
MOBO: Gigabyte z490 Vision D
CPU: intel 10700k
GPU: Sapphire nitro RX580
RAM: CORSAIR VENGEANCE RGB 2 x 16GB DDR4 3200MHz CL16 DIMM
NVME 1: MacOS - WDBlack SN750 500GB
NVME 2: Windows - WD blue SN550 250GB
SSD 3: Mac Storage - Samsung 860 Evo 2.5” 1TB
Hello @BurtRichalds,

Some questions/comments:
  • Does the grey screen occur when system has been idle for a few minutes and is preparing to sleep?
  • Or does it occur even when you are actively using the system?
  • Has this problem always been present, or did it begin recently?
  • We generally discourage the use of WD SN750 NVMe SSDs due to some user-reported issues, but if the problem started recently after many months of smooth sailing, then we can rule out the SN 750.
Suggestions:
  • Try disabling NVMeFix.kext from OpenCore config.plist
  • Check memory. There's a free version of MemTest86 here. There are other alternatives that can be found by googling.
 
Back
Top