Contribute
Register

[SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

@CaseySJ , hmm ran 0.5.7 - 0.6.1 without a hitch, now having a few problems with 0.6.2 in works fine until Apple logo, then no progress bar. I'm just trying to -v verbose now but proving difficult, anybody else with this or is it possibly the new 0.7.6 USBInject ?? Just thought I'd ask whilst I tinker in plist

EDIT: Solved. A Typo in a kext.
 
Last edited:
My Build
Z390 DESIGNARE |  i9 9900K |  Radeon Other
ziggenpuss said:
@CaseySJ , hmm ran 0.5.7 - 0.6.1 without a hitch, now having a few problems with 0.6.2 in works fine until Apple logo, then no progress bar. I'm just trying to -v verbose now but proving difficult, anybody else with this or is it possibly the new 0.7.6 USBInject ?? Just thought I'd ask whilst I tinker in plist

EDIT: Solved. A Typo in a kext.
Click to expand...
Is the typo present in the OpenCore 0.6.2 Zip that I posted?
 
Hi all!

Updating clover to 5123 gave the common Quirks issue so I downgraded. Might need to switch to OC at some point, just haven't had the time. Anyone knows if a new version will autodetect the current setup and not break the previous plist?

More importantly though, the "install OSX" partition doesn't show up in Clover when I'm updating to 10.15.7. Any ideas here?
 
Main
Z390 DESIGNARE |  i7 9700K |  HD 630
skulaksiz said:
Hi all!

Updating clover to 5123 gave the common Quirks issue so I downgraded. Might need to switch to OC at some point, just haven't had the time. Anyone knows if a new version will autodetect the current setup and not break the previous plist?

More importantly though, the "install OSX" partition doesn't show up in Clover when I'm updating to 10.15.7. Any ideas here?
Click to expand...
use OpenCore instead
 
Just tried the 0.6.2 mini-guide and get a black screen. Is that guide enough or should it be followed by the sticky guide from the first page?

I only get the three options: Windows, EFI, openshell.efi, keyboard strokes aren't accepted, and after a few seconds of the "picker", I get black screen...
 
Last edited:
Main
Z390 DESIGNARE |  i7 9700K |  HD 630
@CaseySJ
Hi.
Can you please tell me what I need to change after switching to the GPU?
I have been using the iGPU for over a year. I have now bought the rx570.
I don't have JPG preview working now.
Defined as Mac mini (2018).

Thank you!
 
3908700 said:
@CaseySJ
Hi.
Can you please tell me what I need to change after switching to the GPU?
I have been using the iGPU for over a year. I have now bought the rx570.
I don't have JPG preview working now.
Defined as Mac mini (2018).

Thank you!
Click to expand...
Are you using Clover or OpenCore?
 
CaseySJ said:
*** Thunderbolt DROM Micro-Guide for Gigabyte GC-Titan Ridge V1.0 ***
Please do not quote this micro-guide in its entirety. Post a link instead.​
Click to expand...
Posted this in a different thread- realized a week later that I’d probably get a response if I actually quoted the procedure I’m stuck on. Hopefully @CaseySJ or @djlild7hina can chime in :)

Here's what else is happening.

- Before I flashed it, I always had to unplug / replug the card right after I powered it up for the card to work. That still applies, but now, I can't even see the BIOS or any of the verbose mode during boot (which I always leave on). In fact, the monitors shut off due to no signal, then pop on once MacOS is booted. I guess this is a side-effect of using the flashed BIOS and the MiniDisplayPort cables routing from the video card to the Titan Ridge (if I need the BIOS, I can plug an HDMI in directly- so that's not the end of the world).

- If I follow what’s quoted, I can't get anything to connect to my Titan Ridge in any capacity. (I'm sure it's related to setting it to PC00 as @CaseySJ and I discussed previously in a different thread), but I'm wondering if I did the process wrong.

- In System Report on the Hackintosh, the speed shows as 20Gb/s x2. I'm assuming this is also normal?

- As stated at the beginning, hot plug is completely gone. Before the flash, if I unplugged/replugged everything came back normally. Now, I have to either plug in an HDMI or just hold the power button for 5 seconds .... then because of the connected Thunderbolt 3 dock not powering on boot (an issue I had when TB3 was fully functioning with the old firmware), I have to unplug the Thunderbolt 3 cable when I power up, wait a second or 2, then plug it in :lol:

Any advice would be great lol. As it stands now, I'm using the original AML files @CaseySJ supplied me earlier in the other thread and it's running all my devices like it did, except now with Thunderbolt 3 showing up in the System Report & no hot-plug at all.... so I'm getting SOMEWHERE LOL
 
You must log in or register to reply here.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top