- Joined
- Feb 11, 2014
- Messages
- 278
- Motherboard
- Z390 Designare
- CPU
- i7-9700
- Graphics
- Radeon Pro WX 9100
- Mac
- Mobile Phone
Here is what I am getting.The Thunderbay 4 has read/write speeds as shownView attachment 473133
Here is what I am getting.The Thunderbay 4 has read/write speeds as shownView attachment 473133
Sure, please do this:The 10.14.6 (mojave) system I am running has removed the kext you listed. And run Kext Utility to rebuild the kernel cache.
But in the beginning, because it could not start, I restored these kexts from the backup and then deleted them. . . After a few loops, I am not sure to run Kext Utility every time. Later I found a terminal command in your original post
cd /
kextcache -i/volume/Mac S970
This problem can be solved, but I don't know how to enter it or the exact format. Can you teach me?
cd /
kextcache -i /Volumes/"Mac S970"
Feel free to remove both of these files:I'm sure I booted from a USB flash drive. You can also enter macOS recovery
Similarly, using SSDT-USBW.aml will not start the system. The other files in Catalina 10.15.4 Fresh Install.zip run very stably
My Magic Mouse 1 and Apple Trackpad 1 have always worked. Just wondering why this is not consistent across all users.I have Magic Mouse 1 and 2. Both have the same problem, they will not connect. I have suspected that the wifi BT card has been causing the sleep problems (without any legitimate reason to do so) and have tried three of the WiFi BT cards from Amazon that claim to work with Hackintosh but I have the same results with all of them.
Hello @Mace,Hello, @CaseySJ
Is there no progress on using SSDT to activate the Thunderbolt bus? The firmware that I modified was invalid, and I could only flash it back to the original version.
Hello @rogers76, have you seen @jaymonkey's VGTab guide here:Hi @CaseySJ,
I use your guide with my new Configuration (Z390+Core i9). Everything is great and working. Thunderbolt Hotplug is very good. Thank you for all your work.
I have issue with your Vega64 enhance process si I use @mattystonnie AMD Radeon Performance Enhanced SSDT guide with VGTab to solve Noisy Vega Fan. I don't find anywhere a guide with advice value for VGTab and I want to check if my values are good (I find them on a german forum). Is anybody can advice me?
With this method only DP port are working (not the HDMI).
Are you using Layout ID 11? If you're not sure, please post your config.plist but remove serial numbers from SMBIOS before posting.I have a question about audio with your guide. I think my audio map is not good, I use the green audio output to connect my speaker but in Mac OS sound prefpan I must check headphone output to have sound on green audio output. And the front panel headphone output don'work (I test all audio setting in mac os audio prefpan) ! Have you an idea to solve it ?
...
The CNVW module should ideally be disabled by placing SSDT-Z390-DESIGNARE-NO-CNVW.aml into CLOVER/ACPI/patched.
Unfortunately not because that's an Intel CNVi slot rather than a general purpose M.2 slot. So it will only accommodate CNVi devices.Is it possible to replace the onboard Intel Wi-Fi 6 802.11ax on Z490 with a macOS compatible m.2 like the BCM94350ZAE?
Thanks for your answer.Hello @rogers76, have you seen @jaymonkey's VGTab guide here:
https://www.tonymacx86.com/threads/...vega-power-and-fan-control-properties.267519/
Are you using Layout ID 11? If you're not sure, please post your config.plist but remove serial numbers from SMBIOS before posting.