Contribute
Register

[SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

evlthoma said:
I can ping my other Macs, just not this hack. No anti virus, Internet protection, or security software installed.
Click to expand...
Please type ifconfig and post the output. You may remove ether (MAC) addresses from the output.
 
CaseySJ said:
You physically pulled the plug from the wall, fed the dogs, came back, and it was still glowing? You have Ironman on the left and perhaps his Fusion Reactor on the right! :)
Click to expand...
No kidding, right.... I'm going to try it again (tomorrow) but with a time-lapse setup with my DJI camera, I have to see how long they last..

Okay V4 reboot done.
Thunderbolt empty, PCI does show the items on the (e.g. Ethernet), Dock won't respond when a USB is plugged in.

Log output attached.
 

Attachments

  • tb-log-4.txt
    5 KB · Views: 50
  • Ceres_SysInfo_PCI_4.jpg
    Ceres_SysInfo_PCI_4.jpg
    175.2 KB · Views: 51
Elias64Fr said:
As you have a biggest 1200W PS, that probably included biggest capacitors that we can imagine, you should press power button (case button not power supply) with power cable unplugged to quick discharge them :)
Click to expand...
Actually I did press power, and reset, flipped the power switch on the Power Supply (cord detached) to try and drain the cap, but nothing seemed to impact the flow of juice to the memory.
 
svandive said:
No kidding, right.... I'm going to try it again (tomorrow) but with a time-lapse setup with my DJI camera, I have to see how long they last..

Okay V4 reboot done.
Thunderbolt empty, PCI does show the items on the (e.g. Ethernet), Dock won't respond when a USB is plugged in.

Log output attached.
Click to expand...
This one requires cold boot to completely reset the Thunderbolt controller.
svandive said:
Actually I did press power, and reset, flipped the power switch on the Power Supply (cord detached) to try and drain the cap, but nothing seemed to impact the flow of juice to the memory.
Click to expand...
Does detaching the 24-pin motherboard cable help?
 
CaseySJ said:
Please type ifconfig and post the output. You may remove ether (MAC) addresses from the output.
Click to expand...

I'm not worried about the MAC address...

Code: 
evan@Evans-iMac ~ % ifconfig


lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384


    options=1203<RXCSUM,TXCSUM,TXSTATUS,SW_TIMESTAMP>


    inet 127.0.0.1 netmask 0xff000000


    inet6 ::1 prefixlen 128


    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1


    nd6 options=201<PERFORMNUD,DAD>


gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280


stf0: flags=0<> mtu 1280


XHC20: flags=0<> mtu 0


XHC0: flags=0<> mtu 0


en2: flags=8823<UP,BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500


    options=400<CHANNEL_IO>


    ether 48:d7:05:e3:e3:e3


    nd6 options=201<PERFORMNUD,DAD>


    media: autoselect (<unknown type>)


    status: inactive


en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500


    options=40b<RXCSUM,TXCSUM,VLAN_HWTAGGING,CHANNEL_IO>


    ether b4:2e:99:34:cf:62


    inet6 fe80::4cc:6d56:26a9:4b31%en0 prefixlen 64 secured scopeid 0x7


    inet6 2601:805:c200:6ea0:1c7b:1075:6f95:5f3c prefixlen 64 autoconf secured


    inet6 2601:805:c200:6ea0:59f4:a37b:87bd:3ada prefixlen 64 autoconf temporary


    inet6 2601:805:c200:6ea0::e500 prefixlen 64 dynamic


    inet 192.168.86.6 netmask 0xffffff00 broadcast 192.168.86.255


    nd6 options=201<PERFORMNUD,DAD>


    media: autoselect (1000baseT <full-duplex,flow-control,energy-efficient-ethernet>)


    status: active


p2p0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 2304


    options=400<CHANNEL_IO>


    ether 0a:d7:05:e3:e3:e3


    media: autoselect


    status: inactive


awdl0: flags=8902<BROADCAST,PROMISC,SIMPLEX,MULTICAST> mtu 1484


    options=400<CHANNEL_IO>


    ether 6e:da:ef:24:f8:94


    nd6 options=201<PERFORMNUD,DAD>


    media: autoselect


    status: inactive


llw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500


    options=400<CHANNEL_IO>


    ether 6e:da:ef:24:f8:94


utun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380


    inet6 fe80::cf74:e6fa:47f0:ebcb%utun0 prefixlen 64 scopeid 0xb


    nd6 options=201<PERFORMNUD,DAD>


utun1: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 2000


    inet6 fe80::a266:a34d:f407:1c58%utun1 prefixlen 64 scopeid 0xc


    nd6 options=201<PERFORMNUD,DAD>


utun2: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380


    inet6 fe80::f95d:50a6:4cd1:7c83%utun2 prefixlen 64 scopeid 0xd


    nd6 options=201<PERFORMNUD,DAD>


utun3: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380


    inet6 fe80::dbec:3f95:8818:8bb9%utun3 prefixlen 64 scopeid 0xe


    nd6 options=201<PERFORMNUD,DAD>


utun4: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380


    inet6 fe80::7667:42c7:4373:8b5c%utun4 prefixlen 64 scopeid 0xf


    nd6 options=201<PERFORMNUD,DAD>


utun5: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380


    inet6 fe80::388d:8b7a:765f:b6a%utun5 prefixlen 64 scopeid 0x10


    nd6 options=201<PERFORMNUD,DAD>


evan@Evans-iMac ~ %
 
jlr said:
That doesn't seem to have made a difference unfortunately
Click to expand...
  • Is native NVRAM enabled?
  • Are KernelPM and AppleIntelCPUPM checkboxes unchecked in Clover Configurator --> Kernel & Kext Patches?
  • Please post screenshot of /Library/Extensions.
  • Also feel free to compress and upload your CLOVER folder from EFI partition of the Catalina SSD. You may remove serial numbers from config.plist prior to posting.
 
CaseySJ said:
This one requires cold boot to completely reset the Thunderbolt controller.

Does detaching the 24-pin motherboard cable help?
Click to expand...
Let's find out. In the photo you can actually see a 24PIN cable detached, that is a remnant that needs to be cleaned up next time I take the unit off the wall (not a simple task unfortunately)

Let me get to a true Cold Boot.
 
Last edited:
CaseySJ said:
That's progress!

The first Ethernet port (i211, closest to WiFi antenna port) requires SmallTreeIntel82576.kext. The other one (i219, closest to orange audio jack) requires IntelMausiEthernet.kext.

Which one is not working?
Click to expand...

The i211 is not working
i will try the Kext

Any way ro controll the case Leds?!
 
CaseySJ said:
This one requires cold boot to completely reset the Thunderbolt controller.

Does detaching the 24-pin motherboard cable help?
Click to expand...
I was able to detach the Aux 24v and the 24pin and that got me to zero. Attached is the log from this boot.

With Version 3 and Version 4 I've not seen the Ports in Thunderbolt (SysInfo), is that expected? I would think not.
 

Attachments

  • tb-log-5.txt
    5.4 KB · Views: 57
evlthoma said:
I'm not worried about the MAC address...
Bash: 
evan@Evans-iMac ~ % ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
    options=1203<RXCSUM,TXCSUM,TXSTATUS,SW_TIMESTAMP>
    inet 127.0.0.1 netmask 0xff000000
    inet6 ::1 prefixlen 128
    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
    nd6 options=201<PERFORMNUD,DAD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
XHC20: flags=0<> mtu 0
XHC0: flags=0<> mtu 0
en2: flags=8823<UP,BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500
    options=400<CHANNEL_IO>
    ether 48:d7:05:e3:e3:e3
    nd6 options=201<PERFORMNUD,DAD>
    media: autoselect (<unknown type>)
    status: inactive
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    options=40b<RXCSUM,TXCSUM,VLAN_HWTAGGING,CHANNEL_IO>
    ether b4:2e:99:34:cf:62
    inet6 fe80::4cc:6d56:26a9:4b31%en0 prefixlen 64 secured scopeid 0x7
    inet6 2601:805:c200:6ea0:1c7b:1075:6f95:5f3c prefixlen 64 autoconf secured
    inet6 2601:805:c200:6ea0:59f4:a37b:87bd:3ada prefixlen 64 autoconf temporary
    inet6 2601:805:c200:6ea0::e500 prefixlen 64 dynamic
    inet 192.168.86.6 netmask 0xffffff00 broadcast 192.168.86.255
    nd6 options=201<PERFORMNUD,DAD>
    media: autoselect (1000baseT <full-duplex,flow-control,energy-efficient-ethernet>)
    status: active
p2p0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 2304
    options=400<CHANNEL_IO>
    ether 0a:d7:05:e3:e3:e3
    media: autoselect
    status: inactive
awdl0: flags=8902<BROADCAST,PROMISC,SIMPLEX,MULTICAST> mtu 1484
    options=400<CHANNEL_IO>
    ether 6e:da:ef:24:f8:94
    nd6 options=201<PERFORMNUD,DAD>
    media: autoselect
    status: inactive
llw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500     options=400<CHANNEL_IO>
    ether 6e:da:ef:24:f8:94
utun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
    inet6 fe80::cf74:e6fa:47f0:ebcb%utun0 prefixlen 64 scopeid 0xb
    nd6 options=201<PERFORMNUD,DAD>
utun1: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 2000
    inet6 fe80::a266:a34d:f407:1c58%utun1 prefixlen 64 scopeid 0xc
    nd6 options=201<PERFORMNUD,DAD>
utun2: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
    inet6 fe80::f95d:50a6:4cd1:7c83%utun2 prefixlen 64 scopeid 0xd
    nd6 options=201<PERFORMNUD,DAD>
utun3: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
    inet6 fe80::dbec:3f95:8818:8bb9%utun3 prefixlen 64 scopeid 0xe
    nd6 options=201<PERFORMNUD,DAD>
utun4: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
    inet6 fe80::7667:42c7:4373:8b5c%utun4 prefixlen 64 scopeid 0xf
    nd6 options=201<PERFORMNUD,DAD>
utun5: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
    inet6 fe80::388d:8b7a:765f:b6a%utun5 prefixlen 64 scopeid 0x10
    nd6 options=201<PERFORMNUD,DAD>
evan@Evans-iMac ~ %
Click to expand...
Please try this:
  • Enable Firewall from System Preferences --> Security & Privacy --> Firewall
  • Then click Firewall Options... and make sure the two items in red are unchecked.
  • Then disable Firewall once again.
Screen Shot 2020-05-04 at 4.01.57 PM.pngScreen Shot 2020-05-04 at 4.02.01 PM.png
 
You must log in or register to reply here.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top