Asus X299 - Support

[djlild7hina]

So I did the firmware flash of the Titan Ridge under Windows and it was successful. Did all the BIOS settings (triple checked).

In System Report -> Thunderbolt, I still get: "Thunderbolt: No drivers are loaded."

When I connect my Caldigit dock, it lights up and the hard drive attached to it lights up, but nothing is showing up. Am I missing something here? I'm in PCIE Slot 2 on the X299 SAGE 10G board.

HELP! LOL

Thunderbolt devices won’t show up under system report -> Thunderbolt since we’re doing a workaround. Make sure you have the Thunderbolt SSDT adjusted for the Sage (should be on the GitHub repo) in your EFI. You can verify using IOReg and address PCI0.RP05

 

[djbuddha]

Thunderbolt devices won’t show up under system report -> thunderbolt since we’re doing a workaround. Make sure you have the thunderbolt ssdt adjusted for the Sage (should be on the GitHub repo) in your EFI. You can verify using IOReg and address PCI0.RP05

Ok I have the aml file ... how am I installing this? I haven't done many AML files as of yet ... got so swamped with work I've been slowly working on this machine. Had other hardware issues I had to iron out before I could continue.

 

[djlild7hina]

Ok I have the aml file ... how am I installing this? I haven't done many AML files as of yet ... got so swamped with work I've been slowly working on this machine. Had other hardware issues I had to iron out before I could continue.

Copy these files to EFI->Clover->ACPI->Patched

 

[djbuddha]

Copy these files to EFI->Clover->ACPI->Patched

Any other steps, or just reboot?

 

[macmaxxx]

Guys, get a look on my EFI folder. I can't finish install:

i9-9940X
Asus X299 Prime A
Gigabyte Radeon Vega 64

 

[djbuddha]

Copy these files to EFI->Clover->ACPI->Patched

Rebooted, no sign of any change here ... anything else I need to do?

 

[macmaxxx]

Do not OC or anything until you have macOS set up and running. You're jumping the gun here.

I don' worry about OC, I make this everyday on PC gamers for my clients. Only think is X299 hackintosh install. Can you look for my EFI folder? I can't finish install

i9-9940X
Asus X299 Prime A
Gigabyte Radeon Vega 64

 

[djbuddha]

From KGP's guide ...

From my machine:

I wonder why my card won't load.... TB3 header is connected, firmware is flashed and the BIOS settings on the board are exactly what he said.... and I'm in slot 2

 

[mm2margaret]

From KGP's guide ...

View attachment 438658

From my machine:

View attachment 438659,

I wonder why my card won't load.... TB3 header is connected, firmware is flashed and the BIOS settings on the board are exactly what he said.... and I'm in slot 2

So I'm hoping you have a drive or some kind of TB device to test with. If you do, try it first in Windows, and make sure you set the permissions there in Windows to all (everyone, every thing). See if you can then access the drive. Don't proceed to the Mac side until you can reliably access the drive. You should be able to unload it, then re-plug it in, and reload it, per normal behaviour for a TB device.

If you have any trouble, double check your settings in the BIOS. Get it to work normally in Windows, then move to the Mac. Check the drivers, the TB utility (in Windows), etc. You should be able to start the utility and then you should see your drive/device attached to one of the two TB ports. Until this works, there's no point in moving to the Mac. Once it works here, in Windows, you've got a good shot of it working on the Mac side.

At first, on the Mac side, connect the device (s) before starting up. Then look on the Mac side to see if your drive/device is there. If it is, you can try to eject it and reload it, but don't be surprised if it doesn't work. Doesn't for me, while others claim it does for them. Not sure why, but that's the way it works for some sometimes. Could be my TB1 drive, not sure about that. But try it this way, and see if you can at least get a drive to show up on the Mac side.

Good luck!

EDIT: And, you should keep in mind that you might have a bad card....doesn't occur very often, but it happens....

 

[djbuddha]

S0 I'm hoping you have a drive or some kind of TB device to test with. If you do, try it first in Windows, and make sure you set the permissions there in Windows to all (everyone, every thing). See if you can then access the drive. Don't proceed to the Mac side until you can reliably access the drive. You should be able to unload it, then re-plug it in, and reload it, per normal behaviour for a TB device.

If you have any trouble, double check your settings in the BIOS. Get it to work normally in Windows, then move to the Mac. Check the drivers, the TB utility (in Windows), etc. You should be able to start the utility and then you should see your drive/device attached to one of the two TB ports. Until this works, there's no point in moving to the Mac. Once it works here, in Windows, you've got a good shot of it working on the Mac side.

At first, on the Mac side, connect the device (s) before starting up. Then look on the Mac side to see if your drive/device is there. If it is, you can try to eject it and reload it, but don't be surprised if it doesn't work. Doesn't for me, while others claim it does for them. Not sure why, but that's the way it works for some sometimes. Could be my TB1 drive, not sure about that. But try it this way, and see if you can at least get a drive to show up on the Mac side.

Good luck!

EDIT: And, you should keep in mind that you might have a bad card....doesn't occur very often, but it happens....

I have a Caldigit Thunderbolt 3 dock I use currently with my 2017 MBP which I'm going to eventually use with this new machine. Funny thing, if I plug a USB-C drive into the Titan Ridge, it comes up (full speed too) but that isn't overly surprising.

Looks like I'm re-installing Windows 10 on an external to try again. Weird thing, I had a LOT of issues getting the firmware to install (the installer just wasn't having it) but it did confirm the firmware update eventually (had to deep dive in Device Manager to get the driver installed for some strange reason).