Mojave Intel HD 530

[larlid]

Try the following for your listed Intel HD 4400 graphics in Profile

1. Boot into Mojave
2. Start Clover configurator, mount EFI of System Disk
3. Open EFI -> EFI -> CLOVER -> config.plist with Clover configurator.
4. Go to the top half of Left Panel [SECTIONS]
5. Scroll down to Devices >FakeID > IntelGFX and type in 0x04128086
6. Scroll down to Graphics> [√]InjectIntel .........>>>>>>> [Ig-platform-id] and type in 0x0D220003
7. Scroll down to bottom Left panel and locate the 2nd short arrow > Click Save As.. config.plist>OK

Thanks for your answer.
The system boots and works but the same problem remains. Artifacts in finder and 1024x768 only.
Lars.

 

[cmn699]

Thanks for your answer.
The system boots and works but the same problem remains. Artifacts in finder and 1024x768 only.
Lars.

• If you have not already changed your BIOS_Graphics to show DVMT Pre-allocated Memory of 64 M (preferably 128M), please do so and see if the Problem goes way. (Please NOTE: your Profile DOES Not show your Motherboard)
• If after changing BIOS options as above, with Initial Display as IGFX and DVMT Pre-Allocated =64 to 128M , you still get no full resolution, then try the following:
• Boot to CBM screen.
• Go to Options>GraphicsInjector->and change *-platform-id =0x0a260006
• Return to CBM and boot and take a screen captures of
  • Apple>About ThisMac_Overview_macOSMojave _Version
  • System Report..>Hardware>Graphics and Display
• Upload the Images

 

[larlid]

cmn699: Thanks a lot!
I changed graphics ram in BIOS to 128MB.
I still didn't work.
After several tries I used these settings succesfully:
Devices > fakeID > IntelGFX > 0x0
Graphics > InjectIntel checked > ig-platform-id to 0x19160000 (I tried this setting since the processor is really a mobile processor)
Full 3840x2160 resolution.

Thanks a lot. I wouldn't have made it without your help cmn699

 

[cmn699]

cmn699: Thanks a lot!
I changed graphics ram in BIOS to 128MB.
I still didn't work.
After several tries I used these settings succesfully:
Devices > fakeID > IntelGFX > 0x0
Graphics > InjectIntel checked > ig-platform-id to 0x19160000 (I tried this setting since the processor is really a mobile processor)
Full 3840x2160 resolution.

Thanks a lot. I wouldn't have made it without your help cmn699

Thank you for your final comprehensive post.

• All my previous suggestions were made on a mistaken Intel HD 4400 from your earlier post !
  • Glad you finally updated your profile and posted a step by step fix for the real problem.
• Your post has significant value as it would help readers with answers they are looking for in a Bad Graphics Display with the same hardware.

 

[stevep0070]

cmn699: Thanks a lot!
I changed graphics ram in BIOS to 128MB.
I still didn't work.
After several tries I used these settings succesfully:
Devices > fakeID > IntelGFX > 0x0
Graphics > InjectIntel checked > ig-platform-id to 0x19160000 (I tried this setting since the processor is really a mobile processor)
Full 3840x2160 resolution.

Thanks a lot. I wouldn't have made it without your help cmn699

Sorry to revive an old post but I’ve also got an EliteDesk G2 and i was wondering if you’d be able to share your configuration with me. I had it running with Mojave with a pre-built clover package but I wanted to give Catalina a whirl. I now have graphics issues and it seems like there is a ton of excess stuff in this pre-fab clover file I’m using now that I’ve got a little time to dig into it. Thanks in advance

 

[valroe]

I just set up my Hackintosh yesterday and I have a problem with my HD 530 iGPU not even showing up in the system report. My dGPU (RX 570) works without a problem.
Mojave 10.14.5, i5-6500 on AsRock H170M-ITX/DL. I use HDMI for the iGPU.

config.plist and installed Kexts attached. The AppleIntelKBLGraphics….kexts are in my S/L/E.

I tried to find answers in this thread https://www.tonymacx86.com/threads/guide-intel-framebuffer-patching-using-whatevergreen.256490/ but honestly, I don't understand half of it and don't even know where I would have to start. Most people seem to have issues with the iGPU not running correctly but, again, it doesn't even show up in my system.

In the Clover boot menu, the HD 530 is recognized when I disconnect my RX 570 and run on the iGPU. But then, when I boot into macOS, my screen receives no input.

Any help and assistance would be greatly appreciated!

 

[deeveedee]

Deleted

 

[cleecayce]

Hello!

I have tried several combinations and I either get “Display 7MB” “Intel HD Graphics 530 7MB” or nothing at all. Can someone please help me out here?

I have Lilu and Whatevergreen’s latest versions. installed in the “Other” folder on the EFI partition.

I am on 10.14.0 and I am not sure how to update to 10.14.6 after I restart.

The PC is an HP AiO so I can’t exactly swap anything out for something else if I needed to.

Any help with either of these issues would be greatly appreciated!!!

 

[Gigamaxx]

Hello!

I have tried several combinations and I either get “Display 7MB” “Intel HD Graphics 530 7MB” or nothing at all. Can someone please help me out here?

I have Lilu and Whatevergreen’s latest versions. installed in the “Other” folder on the EFI partition.

I am on 10.14.0 and I am not sure how to update to 10.14.6 after I restart.

The PC is an HP AiO so I can’t exactly swap anything out for something else if I needed to.

Any help with either of these issues would be greatly appreciated!!!

Don you have bios settings for allocated ram for IGPU graphics? Set to 64mb minimum.

 

[cleecayce]

Don you have bios settings for allocated ram for IGPU graphics? Set to 64mb minimum.

My bios has next to no options TBH. I am honestly surprised I got MacOS intalled in the first place. So no I don’t have that configured.
Would a BIOS update add more options?