[Guide] Lenovo V330-15IKB using Clover UEFI hotpatch

[Edoardo001]

Ooh, it works!
Thanks a lot!
Now I can use Mojave.. ^_^

Great, all works good?

 

[Edoardo001]

So, If you had cloned Mojave to the new NVMe you shouldn't have any issues? This Intel NVMe has Mojave native support?

Use nvme flag in clover, for me worked good.(haven't tested without it)

 

[ohm1935]

Great, all works good?

Yes Thanks.
It works like Real MAC!

 

[Sniki]

I've edited removing the "hda-gfx" flags in properties, but still no luck
SOLVED: delete all the property flags under "device" in config.plist
Important: Important, after installation you must re put the "hda-gfx" properties to get uhd 620 working

That is wrong, you don't need to delete devices, you remove hda-gfx from two devices GPU and Audio which i did on latest files uploaded on the repository, use all latest kext, latest clover from sourceforge and you should be good 2 go.

hi sniki Apple BCM94360CS2 + M2/NGFF Adapter works with some handwork (cutting/smoothing edges of the adapter and card so it can fit).
I bought this card how to cut smooth edges of the adapter Apple BCM94360CS2 and how to fit
please make a tutorial or screen shot I couldn't understand

please reply

Honestly i had to cut it till i fit it (almost touched the antenna on the right side so it could fit.)
I first removed the fan, tightened the card (after the cutting, keep in mind cut both adapter and card to make room.) put the screw then placed the fan as it's a small bump when trying to push it down to put the screw on the adapter or motherboard, after you tighten it, you put the fan back in place.

Hi, i'm using same laptop.
V330 (81AX), i5-8250U, 12GB Ram, 256 NVMe.
I followed your steps, but my laptop not booting.
What should i can do?

View attachment 410233

End RandomSeed log and stucking..

Add ram infos into your SMBIOS/Memory on config.plist

Use this config.plist (attached)

If after this you have errors like "Forcing CS
runtime...(same uuid) "(don't remember), delete properties in config.plist > devices

No need to remove properties, hda-gfx properties only.

 

[ohm1935]

That is wrong, you don't need to delete devices, you remove hda-gfx from two devices GPU and Audio which i did on latest files uploaded on the repository, use all latest kext, latest clover from sourceforge and you should be good 2 go.

Honestly i had to cut it till i fit it (almost touched the antenna on the right side so it could fit.)
I first removed the fan, tightened the card (after the cutting, keep in mind cut both adapter and card to make room.) put the screw then placed the fan as it's a small bump when trying to push it down to put the screw on the adapter or motherboard, after you tighten it, you put the fan back in place.

Add ram infos into your SMBIOS/Memory on config.plist

No need to remove properties, hda-gfx properties only.

Thanks. Have a nice day!
From South Korea.

 

[innovativedave]

@Sniki When the installer finishes it reboots when it says “2 minutes remaining”. Then it boots onto the ssd and the Apple logo appears stating “15 minutes remaining”. Though, it keeps rebooting at this point over and over again. The verbose flag doesn’t show any error at this point as it shows the Apple logo with the percentage. It manages to add the recovery drive aswell. Should I let the laptop see if it will complete the installation or what can I do to resolve this problem. My system has 512gb ssd with 16gb ram and same i5 processor.

 

[Edoardo001]

@Sniki When the installer finishes it reboots when it says “2 minutes remaining”. Then it boots onto the ssd and the Apple logo appears stating “15 minutes remaining”. Though, it keeps rebooting at this point over and over again. The verbose flag doesn’t show any error at this point as it shows the Apple logo with the percentage. It manages to add the recovery drive aswell. Should I let the laptop see if it will complete the installation or what can I do to resolve this problem. My system has 512gb ssd with 16gb ram and same i5 processor.

I have no competence to help you. My way to troubleshoot is to re try reading more accurately.
Try with latest clover from sourgeforce, or if you use nvme sad try to add nvme flag in clover.

 

[NicoM4491]

Hi to everyone,

I Follow this guide, adding some modifications to fit my model exactly (AX81), have a question for you, my lap temp is between 55º and 65º Celsius, are these temperatures normal?
Also i saw that these model of processor works at full 3.10ghz when in Windows it goes from 1.6ghz to ful throotle 3.10ghz in some tasks, did somebody made a SSDT to patch this?

 

[Sniki]

Hi to everyone,

I Follow this guide, adding some modifications to fit my model exactly (AX81), have a question for you, my lap temp is between 55º and 65º Celsius, are these temperatures normal?
Also i saw that these model of processor works at full 3.10ghz when in Windows it goes from 1.6ghz to ful throotle 3.10ghz in some tasks, did somebody made a SSDT to patch this?

If your model is the one in your profile then it's a completely different laptop, different architecture, different IGPU, different SMBIOS, that means ofc something will be wrong with it.
I don't see other model listed on your signature, just this one.

 

[NicoM4491]

If your model is the one in your profile then it's a completely different laptop, different architecture, different IGPU, different SMBIOS, that means ofc something will be wrong with it.
I don't see other model listed on your signature, just this one.

That was my old laptop, i modified the signature now. is the LENOVO V330-15IKB (81AX) the only difference is that mine only have the UHD620 as video card and display is not Full HD, it's 1366x768.
Everything is working flawless only need to know if the temps are normal.