[Guide] Intel NUC7/NUC8 using Clover UEFI (NUC7i7Bxx,NUC8i7Bxx,etc)

[Ezak91]

@Leesureone i belive you.
i set now my usb-c in bios at first, hdmi as second.
I comment out the PCI and PCIROOT entrys.

i try boot with usb-c and then hot plug hdmi after starting mojave --> only usb-c
i try boot with hdmi and then hot plug usb-c after starting mojave --> only hdmi

any idea or any other mayby?

Thank you!

 

[Leesureone]

I'm kind of out of ideas to suggest except to update Lilu.Kext, Whatevergreen.kext and maybe the version of clover you are booting if you haven't done so recently. Can't hurt but it may not make any difference. Hackintool is another possibility for creating specific Device IDs and video output but it is a bit complex.

 

[Ezak91]

I still have the problem and no glue what can i do. @RehabMan do you have an idea?

[Guide] Intel NUC7/NUC8 using Clover UEFI (NUC7i7Bxx,NUC8i7Bxx,etc)

Did you make sure to select the UEFI boot selections shown in the attached when installing? You can always run install again but double check the correct drivers and Kexts are still installed in your hard drive based EFI folder. I totally did not :(. Ugh. How do I recover? I have an older...

www.tonymacx86.com

 

[Leesureone]

I still have the problem and no glue what can i do. @RehabMan do you have an idea?

[Guide] Intel NUC7/NUC8 using Clover UEFI (NUC7i7Bxx,NUC8i7Bxx,etc)

Did you make sure to select the UEFI boot selections shown in the attached when installing? You can always run install again but double check the correct drivers and Kexts are still installed in your hard drive based EFI folder. I totally did not :(. Ugh. How do I recover? I have an older...

www.tonymacx86.com

The last post from Rehabman was March 13th, he seems to have retired. Your issue is with display output and is best addressed in a different forum. I've suggested Frame Buffer Patching which can be done with Hackintool found on this site. More maybe available there unless another user has some guidance for you.

[Release] Hackintool v3.x.x

HACKINTOOL The Swiss army knife of vanilla Hackintoshing WARNING! Hackintool is not an automated patching tool that does all the work for you. Knowledge is required on how to patch before using it. Please read the Intel Framebuffer patching using WhateverGreen guide before you download this...

www.tonymacx86.com

 

[PWGuy]

Is 10.14.5 fairly straightforward install? Any issues coming from .3, specifically?

 

[Leesureone]

Is 10.14.5 fairly straightforward install? Any issues coming from .3, specifically?

Worked straightforward for me from 14.4, rebooted one time and that was it.

 

[Peg49]

Hi, I'm new to hackintosh and have recently purchased an intel NUC8i5BEK and followed RehabMan guide and have created a bootable USB drive with Mojave.

clover runs and I can launch the the installer. I get the apple logo with progress bar which when completes does nothing, am I doing something wrong? Any help would be much appreciated.

 

[Leesureone]

Hi, I'm new to hackintosh and have recently purchased an intel NUC8i5BEK and followed RehabMan guide and have created a bootable USB drive with Mojave.

clover runs and I can launch the the installer. I get the apple logo with progress bar which when completes does nothing, am I doing something wrong? Any help would be much appreciated.

This guide is outdated now with changes to the bios, Mojave and Clover. See post 383 in this guide for what the various tweaks you will need to make.

[Guide] Installing macOS Mojave (10.14.2) on Intel NUCi5BEH using Clover UEFI + updating to Mojave (10.14.6) on post#2

Hi community, Same problem here, ending on the same line. I have 14.5.02, BIOS 71 I was able to boot using folder from post #333 (after loosing day or two following ReHab guide). Then I installed MacOS and everything else from first post of this thread. I installed wrong (ReHab) Clover 4701 to...

www.tonymacx86.com

 

[Peg49]

This guide is outdated now with changes to the bios, Mojave and Clover. See post 383 in this guide for what the various tweaks you will need to make.

[Guide] Installing macOS Mojave (10.14.2) on Intel NUCi5BEH using Clover UEFI + updating to Mojave (10.14.6) on post#2

Hi community, Same problem here, ending on the same line. I have 14.5.02, BIOS 71 I was able to boot using folder from post #333 (after loosing day or two following ReHab guide). Then I installed MacOS and everything else from first post of this thread. I installed wrong (ReHab) Clover 4701 to...

www.tonymacx86.com

Thanks Leesureone I'm giving it a go now. I'll report back it all is good! Fingers crossed

 

[Peg49]

This guide is outdated now with changes to the bios, Mojave and Clover. See post 383 in this guide for what the various tweaks you will need to make.

[Guide] Installing macOS Mojave (10.14.2) on Intel NUCi5BEH using Clover UEFI + updating to Mojave (10.14.6) on post#2

Hi community, Same problem here, ending on the same line. I have 14.5.02, BIOS 71 I was able to boot using folder from post #333 (after loosing day or two following ReHab guide). Then I installed MacOS and everything else from first post of this thread. I installed wrong (ReHab) Clover 4701 to...

www.tonymacx86.com

Hi Leesureone, So I followed the guide you recommended using my existing clover bootable USB. I downloaded all the files and placed them in the relevant folders in clover. The Bios on the Nuc is the latest and configured as per the walk through. On inserting the USB into the Nuc and booting into clover and make the configurations I get as far as [Part 2] point 2. Once again I get the apple logo with an install bar on completion nothing happens, I don't get an install screen and can't access Disk Utility to format the internal M.2 drive.

Any ideas what could be going wrong? I've tried everything I can think of (apart from starting from scratch)?