[SUCCESS] Gigabyte Designare Z390 (Thunderbolt 3) + i7-9700K + AMD RX 580

[FormerUser-594785]

Thunderbolt:
I have a LaCie Rugged External HD Thunderbolt (I don't know if is 1 or 2).
The Umount and Mount is ok, but when I Boot Computer the Hd icon is like Internal (grey color),
after hot swap the icon is Green color (it's a TM HD)...

 

[xanderevo]

Hi Casey, today I received the BCM94360CS2 with the adapter, wifi works but I have a problem with the bluetooth, could you help me figure this out?

It says bluetooth not available and also in system information this is displayed:

 

[CaseySJ]

Thanks. I have a version of this, and from your description, I'm wondering: Besides changing RP05 to RP21, should I also change DSB0 to DSB1? Where -unless I'm mistaken- my Apollo is showing up on RP21<IOPP<DSB1@1 ??

It's only necessary to change RP05 to RP21. All child-node names must remain unchanged. However, this has less than 0.00000001% chance of fixing Thunderbolt 1 issues!! Because if that problem is due to Legacy Mode being disabled on Titan Ridge, then changing device ID won't help.

-Just finished trying it out. Everything still worked, but no change in hotswapability. I caught it in i/o Reg on power disconnect, but as before, the UAD Apollo 8 Quad (this is the black one with 2 onboard Thunderbolt 2 ports) will not reconnect without a reboot. The secret sauce is in the Mac (Sierra, High Sierra, Mojave) -and Windows 10. CSM support in BIOS is off; CSM on and PCI=Legacy mode doesn't seem to make a difference, FWIW.

Are you using the GC-Titan Ridge or GC-Alpine Ridge card on your motherboard?

GC-Alpine Ridge may actually work with Thunderbolt 1 devices.

As for your UAD Apollo 8 Quad, in my experience motherboards with built-in Thunderbolt seem to be most reliable in the hot swap department.

 

[xanderevo]

This was a quick fix I had the v4 SSDT, deleted that and upgraded to V5, bluetooth is working as well as wifi.

 

[CaseySJ]

@CaseySJ Hi again! Is it possible to enable Firevault on this build?

It should be possible to enable FireVault using a number of EFI drivers that can be installed through Clover Configurator --> Install Drivers. However, I have no experience with this and cannot assist any further. But search this website and you'll find a lot of helpful information.

 

[CaseySJ]

@CaseySJ , just a quick question - are you using any splitter for F_USB to connect your BT from the PCI adapter? I have not noticed one in your list of hardware.

I have ordered one as I do use front panel usb ports , but still thought of asking if there is something reliable that you would recommend.

Thanks

Funny you should ask! Because the Phanteks Evolv X PC case does not have a Reset switch (only a Power switch), I just purchased this little contraption:

https://www.amazon.com/dp/B01MQUANS8/?tag=tonymacx86com-20

It connects to the internal USB header, of which there is one. To share this header with the Bluetooth module, I purchased this:

https://www.amazon.com/dp/B076Q8685Y/?tag=tonymacx86com-20

If you need more than 2 internal USB ports, this is also available:

https://www.amazon.com/dp/B078ZSS5NH/?tag=tonymacx86com-20

Now I can power the system ON/OFF and Reset it with a wireless remote control. It works very well.

 

[Anim8me2]

Funny you should ask! Because the Phanteks Evolv X PC case does not have a Reset switch (only a Power switch), I just purchased this little contraption:

https://www.amazon.com/dp/B01MQUANS8/?tag=tonymacx86com-20

It connects to the internal USB header, of which there is one. To share this header with the Bluetooth module, I purchased this:

https://www.amazon.com/dp/B076Q8685Y/?tag=tonymacx86com-20

If you need more than 2 internal USB ports, this is also available:

https://www.amazon.com/dp/B078ZSS5NH/?tag=tonymacx86com-20

Now I can power the system ON/OFF and Reset it with a wireless remote control. It works very well.

GAH!
This is great. I have a Corsair case and it also has no reset switch. Perfect timing.

 

[flyball]

Hello again
Presently I have a new Monitor. Now my vega 64 Crashes couple times!
And Memory gets Full according Istate and the Screen which hast 4k has the following!

 

[rasta4i]

Hello, everyone I’ve got my system up and running, sometimes I have issues waking from sleep but at the moment I don’t seem to be able to see my 6tb and 10tb drives that I’ve installed on the system or in disk utility. However I can see the 3 and 4 tb drives

 

[avtor]

Funny you should ask! Because the Phanteks Evolv X PC case does not have a Reset switch (only a Power switch), I just purchased this little contraption:

https://www.amazon.com/dp/B01MQUANS8/?tag=tonymacx86com-20

It connects to the internal USB header, of which there is one. To share this header with the Bluetooth module, I purchased this:

https://www.amazon.com/dp/B076Q8685Y/?tag=tonymacx86com-20

If you need more than 2 internal USB ports, this is also available:

https://www.amazon.com/dp/B078ZSS5NH/?tag=tonymacx86com-20

Now I can power the system ON/OFF and Reset it with a wireless remote control. It works very well.

@CaseySJ , that contraption is so cool! Luckily I have the reset button, but this a great option!

I have just received my splitter - exactly the one you have mentioned. I was just a little worrying there were a few mix reviews, but great to hear it is working well. Why don't you put those little contraptions on your hardware list? you can't technically run your box fully without them

Thanks again for all your help!