Contribute
Register

ASUS ROG STRIX Z390-I Gaming Motherboard specs

Status
Not open for further replies.
I can confirm deep sleep also works great!
 
vincek8s said:
Updated yesterday, everything is stable so far.
Click to expand...

Hi, I still have a series of problems with my Z390-I. like USB only at 480Mbps , No iGPU

So, sir, would you mind to share your EFI?

I have the exactly the same configuration as yours (ASUS Z390-I /9900K /RX 580)

BTW, how could I enable the OC of my CPU?
I have setup at BIOS (4.7G 1.25V). But, when I run R15 or Xcode, it only hits 4.2G.
 
Last edited by a moderator:
byuan04 said:
Hi, I still have a series of problems with my Z390-I. like USB only at 480Mbps , No iGPU

So, sir, would you mind to share your EFI?

I have the exactly the same configuration as yours (ASUS Z390-I /9900K /RX 580)

BTW, how could I enable the OC of my CPU?
I have setup at BIOS (4.7G 1.25V). But, when I run R15 or Xcode, it only hits 4.2G.
Click to expand...

I have USB issues, too, all ports will recognise USB 2 devices, but not USB 3 devices. You should be able to have the iGPU enabled while still using the 580, I have had to enable it on mine with a 560 just so I can view images.
 
byuan04 said:
Hi, I still have a series of problems with my Z390-I. like USB only at 480Mbps , No iGPU

So, sir, would you mind to share your EFI?

I have the exactly the same configuration as yours (ASUS Z390-I /9900K /RX 580)

BTW, how could I enable the OC of my CPU?
I have setup at BIOS (4.7G 1.25V). But, when I run R15 or Xcode, it only hits 4.2G.
Click to expand...
Monkey303 said:
I have USB issues, too, all ports will recognise USB 2 devices, but not USB 3 devices. You should be able to have the iGPU enabled while still using the 580, I have had to enable it on mine with a 560 just so I can view images.
Click to expand...

Here's my SSDT for USB, put it in EFI/Clover/ACPI/patched, which will limit USB ports within 15 ports.
Notice: Due to 15 ports limits, one of the Front USB Port can only read USB3.0.
 

Attachments

  • SSDT-UIAC.aml
    699 bytes · Views: 94
  • IMG_2012.jpg
    IMG_2012.jpg
    536.9 KB · Views: 907
dmdacc said:
Here's my SSDT for USB, put it in EFI/Clover/ACPI/patched, which will limit USB ports within 15 ports.
Notice: Due to 15 ports limits, one of the Front USB Port can only read USB3.0.
Click to expand...

Thanks for this, much appreciated. Sadly, it doesn't fix my issues, I suspect I have a possibly dodgy motherboard as still no USB 3 devices show as connected, unless they are on the 2x rear USB 2 ports, but USB 2 work on every port.

Going to try a CMOS clear and also check to see what works in Windows. Thanks again :thumbup:
 
Monkey303 said:
Thanks for this, much appreciated. Sadly, it doesn't fix my issues, I suspect I have a possibly dodgy motherboard as still no USB 3 devices show as connected, unless they are on the 2x rear USB 2 ports, but USB 2 work on every port.

Going to try a CMOS clear and also check to see what works in Windows. Thanks again :thumbup:
Click to expand...
If your Windows works fine with USB3.0, but macOS doesn't, you may go to read @RehabMan's threads, follow the instruction to rename XHCI to XHC, then install USBInjectAll.kext into clover/kext/other. Only after these two steps, then the SSDT will work.
https://www.tonymacx86.com/threads/guide-creating-a-custom-ssdt-for-usbinjectall-kext.211311/
 
dmdacc said:
Going to try a CMOS clear and also check to see what works in Windows. Thanks again :thumbup:
Click to expand...
If your Windows works fine with USB3.0, but macOS doesn't, you may go to read @RehabMan's threads, follow the instruction to rename XHCI to XHC, then install USBInjectAll.kext into clover/kext/other. Only after these two steps, then the SSDT will work.
https://www.tonymacx86.com/threads/guide-creating-a-custom-ssdt-for-usbinjectall-kext.211311/
[/QUOTE]

Thanks! The initial problem I have is, when discovering the ports, the USB 3 devices are not recognized, only USB 2. So it's kind of a non starter. I will redo it again and see if I can spot anything that I've missed. At first, I suspected the USB 3 device I was using was bad/fussy, but I've tried several, including external hard drives and thumb drives and none show up when plugged in, in either finder or the IOregistry explorer. Cheers.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top