HACKINTOSH? HP ELITEDESK 800 G3 MINI

[PowerK6]

Hi there,

What's the OS version? I only tested on 10.13.6.
Try to add -v to the boot args to get the verbose information

 

[remy666]

I managed to get the install working by injecting intel gfx and adding fakeId. I installed Mojave. I can now boot and have the graphic running but not the ethernet.

 

[PowerK6]

I managed to get the install working by injecting intel gfx and adding fakeId. I installed Mojave. I can now boot and have the graphic running but not the ethernet.

Intel HD630 seems can get native support in 10.13.6 and higher without fakeid or intel injection.
I didn't try Mojave yet. But IntelMausiEthernet.kext should support the embedded Intel one.

 

[remy666]

Yep, fakeid and intel injection is required only for the installation. Afterward it's no more necessary since they are natively supported.
My bad, I was using an old IntelMausiEthernet.kext. I used the one from your folder and now everything is fine except for the sleep problem, but it seems there is no solution except disable sleep.

 

[Hneiluj]

Hello guys. Thank you so much for your help.

Remy666 can tou tell me more about your value of fakeid (intelgfx in device ?) and Intel injection (I tried fixintelGfx in acpi and inject Intel with ig-platform-id : 0x19120000 in graphics) or send me your Clover and kexts if your specs are closer than PowerK6 one.

I have the Skylake 6500 with Intel graphic 530 and nvme ssd

Thanks again

 

[Hneiluj]

*I'm trying to install high Sierra

 

[remy666]

Here is my EFI. I managed to get Mojave working on my EliteDesk 800 G3 Mini. It's a Skylake i5 6500 with Intel Graphics 530. My HDD is a Toshiba nvme KXG50ZNV256G I formatted in APFS.
Everything is working except intel wifi/bluetooth (but it's normal) and sleep/wake is also not working (normal again). I haven't checked hdmi audio (my monitor doesn't have audio but the speaker and the 2 headphones of the front panel are working fine.
For the installation I had to add Input FakeID : 0x19120000. It's not in the config.plist of the EFI I uploaded because once installed you can remove the FakeID from the config.plist

 

[surdelmavo]

Looks good:

• m.2 ssd + 2.5" drive possible
• Replaceable HDD and ram
• Dual DP
• Replaceable WLAN-module. I am not sure you can get a compatible one that fits though

I am worried about:
https://8ballpool.onl/ https://discord.software/ https://omegle.onl/

• No sleep, since iGPU. Hopefully Kaby Lake support will come.
  
• Fan noise. The 65w models have an extra fan for cooling.

This would not be good for gaming, but might pass for video editing. Wonder if it could be Hackintoshed.

 

[tnsantos]

Hello, I do have a HP Elitedesk 800 G3 mini 35w. I created the bootable pendrive using UniBeast and managed to boot into install screen successfully. I have then erased the disk using JHFS+ and started installing. The problem is that the installation proccess hangs at about 80%, with 2 minutes remaining from the end.

It gives an error at pop-pup that says: an error occurred while validating install data macos

And in the install log reads:
Failed to download package from linkfile:///Volumes/Image%20Volume/Install%20macOS%20Mojave.app/Contents/SharedSupport/InstallESD.dmg and no alternate source.

Any help?

Nevermind, i managed to install it by replacing the InstallESD.dmg file manually from the install package. Everything is working but I have an issue with usb 3 devices, I have to slowly insert them in order to be detected by the OS. With usb 2 it doesnt happen.

 

[bcar473]

Hello, I do have a HP Elitedesk 800 G3 mini 35w. I created the bootable pendrive using UniBeast and managed to boot into install screen successfully. I have then erased the disk using JHFS+ and started installing. The problem is that the installation proccess hangs at about 80%, with 2 minutes remaining from the end.

It gives an error at pop-pup that says: an error occurred while validating install data macos

And in the install log reads:
Failed to download package from linkfile:///Volumes/Image%20Volume/Install%20macOS%20Mojave.app/Contents/SharedSupport/InstallESD.dmg and no alternate source.

Any help?

Nevermind, i managed to install it by replacing the InstallESD.dmg file manually from the install package. Everything is working but I have an issue with usb 3 devices, I have to slowly insert them in order to be detected by the OS. With usb 2 it doesnt happen.

What do you mean when you say: "replacing the InstallESD.dmg file manually from the install package." Do you insert it into the iboot flash drive? Or somewhere else?