[Guide] Intel Kaby Lake NUC7 using Clover UEFI (NUC7i7BNH, NUC7i5BNK, NUC7i3BNH, etc)

[RehabMan]

Hi again RehabMan, I have migrated to the beta branch and it is correctly showing ES country code, but handoff still doesn't work. Here you have the output of gen_debug. Thank you!

You might need to log out of iCloud on all your devices, then log back in.

And... You didn't update to the beta branch properly... your config.plist is not from the beta branch.

 

[ttavyy]

Mounting EFI is covered in post #1. Please read it.

Hi,

Thank you for your response. I mounted EFI with "diskutil mount EFI" but at start up (in clover) I still cannot see the recovery partition. Also, EFI doesn't remain mounted after reboot.
Could you tell me how I can make that recovery partition visible again in clover?

 

[RehabMan]

Thank you for your response. I mounted EFI with "diskutil mount EFI"

The guide suggests use of mount_efi.sh.

but at start up (in clover) I still cannot see the recovery partition.

Perhaps you didn't press F3.

Also, EFI doesn't remain mounted after reboot.

Not expected.

 

[chanquete69]

You might need to log out of iCloud on all your devices, then log back in.

And... You didn't update to the beta branch properly... your config.plist is not from the beta branch.

RehabMan, thank you really much, I have handoff working!! I have updated config.plist to beta branch also. With this I can update to Mojave on Monday, right? Only install_downloads.sh after installation?

 

[RehabMan]

RehabMan, thank you really much, I have handoff working!!

Great.

I have updated config.plist to beta branch also. With this I can update to Mojave on Monday, right? Only install_downloads.sh after installation?

May not even need that... unless the update wipes out the changes install_downloads.sh makes to AppleHDA Resources.

Note: Please fix your profile so it contains your hardware details.

 

[chanquete69]

Great.



May not even need that... unless the update wipes out the changes install_downloads.sh makes to AppleHDA Resources.

Note: Please fix your profile so it contains your hardware details.

Awesome news, so I am ready for tomorrow release

One more question, I use iStat Menus for monitoring, but on the temperature section I only have SSD Temperature. Is it possible to have CPU temp?

 

[RehabMan]

One more question, I use iStat Menus for monitoring, but on the temperature section I only have SSD Temperature. Is it possible to have CPU temp?

You would need to install the FakeSMC sensor kexts. They are not installed by default. You will find them already downloaded (matching FakeSMC.kext) in your ~/Projects/nuc.git/downloads/kexts folder. Install to /Library/Extensions (kext installation instructions in laptop FAQ).

 

[chanquete69]

You would need to install the FakeSMC sensor kexts. They are not installed by default. You will find them already downloaded (matching FakeSMC.kext) in your ~/Projects/nuc.git/downloads/kexts folder. Install to /Library/Extensions (kext installation instructions in laptop FAQ).

Working, thank you!

 

[chanquete69]

Great.



May not even need that... unless the update wipes out the changes install_downloads.sh makes to AppleHDA Resources.

Note: Please fix your profile so it contains your hardware details.

Hi RehabMan, bad news. After updating, my 4K monitor attached to the NUC has a really horrible pink/purple tone . It was working correctly in high Sierra. Maybe a graphics issue?
EDIT: Changed HDMI port to the non “Protected UHD” labeled one that I was using and it’s working!

 

[RehabMan]

Hi RehabMan, bad news. After updating, my 4K monitor attached to the NUC has a really horrible pink/purple tone . It was working correctly in high Sierra. Maybe a graphics issue?

No "Problem Reporting" files attached.
Read FAQ, "Problem Reporting" again. Carefully. Attach all requested files/output.
https://www.tonymacx86.com/threads/faq-read-first-laptop-frequent-questions.164990/
Use the gen_debug.sh tool mentioned in the FAQ, that way it is less likely you'll omit something.