- Joined
- Jun 14, 2018
- Messages
- 3
- Motherboard
- ASUS P8Z77-V LK (BIOS version: 0812)
- CPU
- INTEL CORE i7-3770K @ 3.5GHz
- Graphics
- NVIDIA G92GL
- Mac
- Mobile Phone
Hi I am trying to create a hackintosh on the 10.13.5 update using UniBeast 8.1.0
My build is in the profile description, I followed the steps at this link:
https://www.tonymacx86.com/threads/...ierra-on-any-supported-intel-based-pc.235474/
I am stuck on STEP 4
The problem is this: when I try to boot off the USB (I am using a USB 2.0 port for the flash drive but also tried usb 3.0)
Here are the UniBeast settings I used to create the drive:
The result with the post-install folder:
The BIOS settings I used:
1) BOOT priority: WDC WD10EZEX (1 TB HDD) > UEFI: KingstonDataTraveler 2.0 (Fast Boot: Disabled)
2) CPU config:
4) SATA config
6) USB config
8) Restore AC power Loss: Power Off
9) Network Stack: Disabled
I'm kinda new to this whole Hackintosh thing, but I wanna get this working I am really motivated,
Thanks for reading and give suggestions on what I can do,
Esen
My build is in the profile description, I followed the steps at this link:
https://www.tonymacx86.com/threads/...ierra-on-any-supported-intel-based-pc.235474/
I am stuck on STEP 4
The problem is this: when I try to boot off the USB (I am using a USB 2.0 port for the flash drive but also tried usb 3.0)
Here are the UniBeast settings I used to create the drive:
The result with the post-install folder:
The BIOS settings I used:
1) BOOT priority: WDC WD10EZEX (1 TB HDD) > UEFI: KingstonDataTraveler 2.0 (Fast Boot: Disabled)
2) CPU config:
Intel Virtualization Technology: Disabled
Hyper-threading: Enabled
Active Cores: All
Intel Adaptive thermal monitor: Enabled
Limit CPUID max: Disabled
Execute Disable bit: Enabled
3) PCH config is on defaultHyper-threading: Enabled
Active Cores: All
Intel Adaptive thermal monitor: Enabled
Limit CPUID max: Disabled
Execute Disable bit: Enabled
CPU power management config:
CPU ratio: Auto, Enhanced Intel SpeedStep Technology and Turbo Mode are: Enabled
CPU C1E, C3 report, C6 report, Package C state support are all on: Auto
CPU C1E, C3 report, C6 report, Package C state support are all on: Auto
4) SATA config
SATA mode selection: AHCI
SMART status check: Enabled
5) System Agent config is on defaultSMART status check: Enabled
Hot Plugs are Disabled
6) USB config
Legacy USB support: Enabled
Legacy USB 3.0 support: Enabled (also tried disabled)
Intel xHCI Mode: Enabled
EHCI Hand-off: Disabled
KingstonDataTraveler 2.0: Auto (but I tried both forced FDD and hard disk settings)
7) Serial Port: DisabledLegacy USB 3.0 support: Enabled (also tried disabled)
Intel xHCI Mode: Enabled
EHCI Hand-off: Disabled
KingstonDataTraveler 2.0: Auto (but I tried both forced FDD and hard disk settings)
8) Restore AC power Loss: Power Off
9) Network Stack: Disabled
I'm kinda new to this whole Hackintosh thing, but I wanna get this working I am really motivated,
Thanks for reading and give suggestions on what I can do,
Esen