Install into a Black Screen

[tupacsoul]

After some more tryes... impossible to run installer. After Apple logo, screen turns black, but led monitor is green.

I've tryed with Lilu, evergreen and some more configurations without result.

Any help?

My hardware:
Gigabyte Z97X-SLI
I7 4790K
Sapphire R9 280X Vapor X

 

[superic]

After some more tryes... impossible to run installer. After Apple logo, screen turns black, but led monitor is green.

I've tryed with Lilu, evergreen and some more configurations without result.

Any help?

My hardware:
Gigabyte Z97X-SLI
I7 4790K
Sapphire R9 280X Vapor X

I have same issue as yours, stuck at apple logo. Could you boot into recovery mode? I am starting to question it is a BIOS setting with gigabyte board.

 

[tupacsoul]

I have same issue as yours, stuck at apple logo. Could you boot into recovery mode? I am starting to question it is a BIOS setting with gigabyte board.

I've not tried. In my Sierra drive I can enter without problem, but in install option, it happens

 

[superic]

I've not tried. In my Sierra drive I can enter without problem, but in install option, it happens

Yes, I have the same issue. When I enter the install drive, it stuck at Apple logo, and I also tried to install a clean version of Sierra and found out that I cannot boot into unibeasg drive either. Also, same happens to the recovery partition.

 

[hughjaas]

After some more tryes... impossible to run installer. After Apple logo, screen turns black, but led monitor is green.

I've tryed with Lilu, evergreen and some more configurations without result.

Any help?

My hardware:
Gigabyte Z97X-SLI
I7 4790K
Sapphire R9 280X Vapor X

Anyone solve this problem yet?
I'm using a 3930k, Gigabyte X79, MSI R9 280X.
I can hear audio when it's done booting, but I can't see anything. I've tried everything.

 

[walaw]

Same problem here. I try a clean install on ga-z270X-ultra-gaming with i7-7700k CPU and GForce 1050Ti with a Clover 4243 High Sierra install Stick - when booting the high-sierra-installation from clover, the Apple-Logo appears on a black background - then restart/reboot after a few seconds.

When booting into the installer with -v (verbose) "++++++++++" appears on the screen + restart after a few seconds.

I have tried to update CPU-definition in plist.config, I should have all the kexts I need, to boot-up the installer and some other tasks - so far without success.

When we check the high-sierra-forums here, we are really a LOT of users facing the same problems. :/

 

[pravbk100]

To all the people having this problem, did you ppl check with connecting monitor to internal graphics?

 

[walaw]

To all the people having this problem, did you ppl check with connecting monitor to internal graphics?

I did - and it made no difference.

 

[tenor0]

Have you tried disabling Internal Graphics in the BIOS and only using your NVIDIA card?

 

[jorgeface]

Same problem here. I try a clean install on ga-z270X-ultra-gaming with i7-7700k CPU and GForce 1050Ti with a Clover 4243 High Sierra install Stick - when booting the high-sierra-installation from clover, the Apple-Logo appears on a black background - then restart/reboot after a few seconds.

When booting into the installer with -v (verbose) "++++++++++" appears on the screen + restart after a few seconds.

I have tried to update CPU-definition in plist.config, I should have all the kexts I need, to boot-up the installer and some other tasks - so far without success.

When we check the high-sierra-forums here, we are really a LOT of users facing the same problems. :/

I had the same problem. In my case was the memory frequency, my ram is 3466Mhz. Setting up manually in config file did the trick.

Hope this helps.