Contribute
Register

[Guide] Intel Skylake NUC6 (and Skull Canyon) using Clover UEFI (NUC6i5SYK, NUC6i7KYK, etc)

Status
Not open for further replies.
Hi Rehabman once High Sierra is released, can i use this guide for Sierra right? Or will you release a new guide for High Sierra?
 
Hi Rehabman once High Sierra is released, can i use this guide for Sierra right? Or will you release a new guide for High Sierra?

Changes for High Sierra already present in the github project.
 
That was done. BIOS was loaded with defaults, you shouldn't question that. Is there anything else I should check?
RehabMan, would you please, reply?
 
That was done. BIOS was loaded with defaults, you shouldn't question that. Is there anything else I should check?

No further ideas for you.
Impossible for me to check everything for you.
 
No further ideas for you.
Impossible for me to check everything for you.
As you previously mentioned you also have NUC6i7KYK, would you please update your BIOS to the latest version and verify it? Just want to make sure it's not platform related.
 
As you previously mentioned you also have NUC6i7KYK, would you please update your BIOS to the latest version and verify it? Just want to make sure it's not platform related.

There doesn't seem to be anything in that BIOS update that I find beneficial.

Note: I'm currently on 0048, which I updated due to the hyperthreading fix that was present.

When 10.13 is released (on Monday), I will create a USB installer with latest Clover and see if there is any issue booting the installer. Easy to try 10.12.6 installer and 10.13.0 installer at that point.
 
Last edited:
No Disk found when install 10.12.6 on my NUC6i7KYK

These days I try to install 10.12.6 on my Skull Canyon and follow the guide. I have a Samsung 951 NVMe hard disk in this NUC and follow the guide to create USB installer. During the creating procedure, I am confused by the description 'If you are trying to use HackrNVMeFamily for the 10.12 installer, forget about it. Use the correct patches in config.plist KextsToPatch.' So I just put 'FakeSMC.kext' and 'IntelMausiEthernet.kext' in 'kexts/others'. And then use Clover Configure to add the related content in the config.plist. Anyway, I still can't see the Samsung 951 when I need to partition the disk.

The Clover version I used is r4210. And the EFI content is attached. Can anyone kindly help me figure out what happened?
 

Attachments

  • EFI.zip
    4 MB · Views: 104
No Disk found when install 10.12.6 on my NUC6i7KYK

These days I try to install 10.12.6 on my Skull Canyon and follow the guide. I have a Samsung 951 NVMe hard disk in this NUC and follow the guide to create USB installer. During the creating procedure, I am confused by the description 'If you are trying to use HackrNVMeFamily for the 10.12 installer, forget about it. Use the correct patches in config.plist KextsToPatch.' So I just put 'FakeSMC.kext' and 'IntelMausiEthernet.kext' in 'kexts/others'. And then use Clover Configure to add the related content in the config.plist. Anyway, I still can't see the Samsung 951 when I need to partition the disk.

The Clover version I used is r4210. And the EFI content is attached. Can anyone kindly help me figure out what happened?

See NVMe guide:
https://www.tonymacx86.com/threads/...h-ionvmefamily-using-class-code-spoof.210316/
 
Status
Not open for further replies.
Back
Top