[GUIDE] [Skylake] El Capitan MSI Z170A-Tomahawk + i5 6600K + GTX 970

[Exmelizo]

Pre Install Setup And Configuration
0) Copy all downloaded files to a spare USB
1) Follow Steps 1 & 2 from this Link (Thanks to tonymacx86)
You should now have a working El Capitan USB Installer
2) In finder you should now find a mounted drive called EFI. If not Run EfiMounter v3 and click mount and choose the corresponding drive.
3) Navigate into /EFI/CLOVER/drivers64UEFI/
4) Delete OsxAptioFix2Drv-64.efi & Copy OsxAptioFixDrv-64.efi to /EFI/Clover/drivers64UEFI
5) Go Back a folder and delete config.plist and replace with the preconfigured config.plist
6) Open Kexts folder and all numbered folders before 10.10 (10.9, 10.8, 10.7 etc)
7) Copy over USBInjectAll.Kext into the 10.10 & 10.11 folder



PreInstall Setup and Configuration - What was the point of step 6?

 

[sneakyvtr]

Finally got audio working on 10.11.4 - Thanks!

EDIT: I spoke to soon, next reboot reverted back to no audio devices

 

[CosmoDreamer]

Finally got audio working on 10.11.4 - Thanks!

EDIT: I spoke to soon, next reboot reverted back to no audio devices

Have you tried the latest MultiBeast ALC892 kext? Works for me.

Note: firstly I installed two kexts from this guide.

 

[PIETRO17]

is this guide specific for your hardware?
my config. is i5 6600, MSI H170 gaming m3, GTX 970, 16 gb and i tried so many times to get things working but nothing. For example, the file OsxAptioFixDvr will work for me? Thanks for all

 

[phramenma]

Hej Leeum,

thank you for sharing this Guide.
If I am not mistaken, as of 10.11.4 the APIC Fix is not needed anymore, am I right?

just a few questions regarding your configs.

1) Why did you delete the SMBIOS entries in the "copyafter"-config?
2) Same for Rt Variables?
3) And System Parameters?

Thank you very much in advance and all the best!

 

[PIETRO17]

Ok, i managed to install El Capitan and boot for the 1st time with -x -v nv_disable=1, but i can't install multibeast's kext because you can't mount efi partition in Safe Mode!! I'm stuck... please give me help!

 

[Leeum]

Sorry everyone. I no longer have a hackintosh as the hard drive i installed it on has died and saving money for a new one.

 

[kotmann]

Hi,

thank you for your guide!

i still have some questions about clover boot loader.
where is it stored? is it stored on the hard drive or is it stored on the bios itself?
i m asking because i m wondering if it is possible do deinstall clover once i have trouble with installing mac os on my machine. what i m wondering is if i am able to restore my machine to the point bevor i tried the mac os installation with regard to the bios etc.


thx in advance

 

[Leeum]

When you create Hackintosh Using Unibeast it is stored on the USB. Once you install OS X and follow the Multibeast steps it installs Clover onto the Hard drive where OS X is installed.

 

[GoTfan4667]

Managed to finally get OS X installed and running thanks to this guide but am still having a few problems. I can't get passed step 10's installation through multibeast. When I go to build>Install I get a fail message "The installation failed. The installer encountered and error that caused the software to fail. Check the multibeast.log install log for more details." Also with EFI Mounter when i go to mount I immediately get a fail message "AppleEvent handler failed. Finder got an error: AppleEvent handler failed (-10000)." Any suggestions on how to fix these issues? Is it because I am booting in safe mode? I can't boot otherwise.

NOTE: I am running AMD graphics. Dunno if that would cause any problems.. Are there drivers for my card? R9 390x.