Contribute
Register

No Audio Devices - Realtek ALC AppleHDA [Guide]

Status
Not open for further replies.
<00 00 00 00> not valid - ok what now??? I’m pretty sure my motherboard uses Audio_ID 1, but this is saying not valid…Should I proceed with step IV and enter "1" anyway even though this says not valid? What step did I miss?
config.plist is a mess, # breaks the tools.
Edit config.plist/Devices/Audio/#Inject/0x0887 to
config.plist/Devices/Audio/Inject/1
 
Hi toleda,
thanks for your support.

1. Added kext-dev-mode=1 again
2. Can’t boot without npci=0x3000/2000 (0x2000 atm)
3. Tried to set dsdt/HDEF with HDEF-Clover method but everything was set correct, already saved it anyway. There is no DSDT for the x79-up4

Here are all steps updated:


1. No output devices
2. OSX 10.11.1, / GA-X79-UP4 - F2 Bios/i7-3930K/Geforce 660Ti 3GB
3. Multibeast 8.0.1 - ALC892
-realtekALC-110 - No audio codec detected
-audio_cloverALC-110 -No audio codec detected

4. attached
5. attached
6. none installed
7. Empty
8. attached
9. No Scripts used
10. -
11. SSDT attached DSDT not installed

Hope this helps you..

Best
L.
 

Attachments

  • Lysid_v2.zip
    2.3 MB · Views: 68
H1. Added kext-dev-mode=1 again
2. Can’t boot without npci=0x3000/2000 (0x2000 atm)
3. Tried to set dsdt/HDEF with HDEF-Clover method but everything was set correct, already saved it anyway. There is no DSDT for the x79-up4
1. kext-dev-mode=1, 10.11 - no effect, remove
2. ncpi=0x3000 disables audio, do not use. npci=0x2000 OK
3. All Intel motherboards have dsdts, see below

no ssdt attached.
EFI/CLOVER/ACPI/origin/dsdt files, attach first and last dsdt file.
 
Bad news, see Post #1/Unsupported/Non working Realtek ALC AppleHDA/3. Asus P8P67 3xxx BIOS: Phantom codec

Thanks very much, this was it. I finally got my audio working.

Flashed 2xxx BIOS but I still couldn't see any audio output device, so I updated AppleHDA.kext with the original one from the installer, and reinstalled ACL889 Multibeast.
 
config.plist is a mess, # breaks the tools.
Edit config.plist/Devices/Audio/#Inject/0x0887 to
config.plist/Devices/Audio/Inject/1

It works! Thank you so much! I suspected it was something simple I was missing.

The config.plist is the original plain vanilla one from the Clover installer. Strange that it would have issues like the "#" one you mentioned. I'll have to find a guide to be able to read and (try to) understand everything in config.plist.

Thanks again!
 
Hi toleda,

- removed kext-dev-mode=1
- updated config.plist in .ZIP _V3
- added all DSDTs to .ZIP _V3
- updated DSDT&config.plist in zip only.

Best
L.
 

Attachments

  • Lysid_V3.zip
    2.4 MB · Views: 74
Hi toleda,
seems like we make some progress, as Sysinfo displays an output now.

1.Added SSDT-3.aml to EFI/CLOVER/ACPI/patched/ and renamed to SSDT.aml
- SSDT-SB-i7.aml ist present also
2. Updated files added.
3. Used Clover/RealtecALC - Terminalexport added.

Here are all steps updated:


1. No output devices
2. OSX 10.11.1, / GA-X79-UP4 - F2 Bios/i7-3930K/Geforce 660Ti 3GB
3. Multibeast 8.0.1 - ALC892
-realtekALC&CloverALC export added



4. attached
5. attached
6. none installed
7. Empty
8. attached
9. attached
10. -
11. SSDT attached



Best
L.
 

Attachments

  • Lysid__V4.zip
    2.1 MB · Views: 81
Used Clover/RealtecALC - Terminalexport added.
Major fail:
Post #1: Realtek ALC AppleHDA Installation
3. Select one method, remove method to try/install a different method

realtekALC disables cloverALC
cloverALC disables realtekALC
SSDT/HDEF is working

Fix.: install native AppleHDA.kext, run cloverALC
Reply with new files.
 
Its finally working, thank you!
Seems the problem was that i tried with Multibeaast&CloverALC.

1.Used Comboupdate and your Script. :)

Do you need the new files anyway?

Thanks!

L.
 
Status
Not open for further replies.
Back
Top