Contribute
Register

[Guide] HP Envy Haswell series J/K/Q/N using Clover UEFI (10.11)

Status
Not open for further replies.
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

Note: Moved guide post #1 from Yosemite guides section.

Post 10.10 questions to the Yosemite guides thread.
Post 10.11 questions here.
 
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

Hi!
I've got a HP j100-ns 15 inch laptop, and I was wondering if it was any chance to use the gtx 750m for the mac system.

Thanks a lot,
Blue
 
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

Hi!) Is there a chance to update to 10.11 via Appstore, or reinstall required?
 
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

1mperial said:
Hi!) Is there a chance to update to 10.11 via Appstore, or reinstall required?
Click to expand...

You can update via the App Store.

Make sure you update to the latest Clover, and update all (kexts/ACPI/etc) from the repo prior.

Make sure your EFI/Clover/kexts/Other is the only directory that exists (the Clover installer will create empty directories 10.11/10.10/etc).

After doing the update, run ./install_downloads.sh again. It will swap BrcmPatchRAM.kext for BrcmPatchRAM2.kext.
 
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

I did it exactly like this. I updated to Clover v3292, i rerun all your scripts. After restart i get following error:
[h=1]"OsxAptioFixDrv: Error - requested memory exceeds our allocated relocation block"[/h]I booted from CLover on my HDD, shall i use Clover from USB?
Is it necessary to add the RTVariables to the config.plist? From this thread: http://www.tonymacx86.com/el-capita...rect-update-os-x-el-capitan-using-clover.html
Thank you
 
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

feloccio said:
I did it exactly like this. I updated to Clover v3292, i rerun all your scripts. After restart i get following error:
[h=1]"OsxAptioFixDrv: Error - requested memory exceeds our allocated relocation block"[/h]I booted from CLover on my HDD, shall i use Clover from USB?
Is it necessary to add the RTVariables to the config.plist? From this thread: http://www.tonymacx86.com/el-capita...rect-update-os-x-el-capitan-using-clover.html
Thank you
Click to expand...

You failed to update OsxAptioFixDrv-64.efi when you updated Clover.

The required RtVariables is already present in the config.plist used by this guide.
 
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

Dear Tonymac86 Team :headbang:
Dear RehabMan

I have an issue patching my SSDT/DSDT.

./disassemle.sh runs without any problems.

But make patch get an error
make: *** No rule to make target `unpatched/.dsl', needed by `patched/.dsl'. Stop.
I have uploaded the files you probably need to help me with my problems.

Thanks patrick
 

Attachments

  • RehabMan.zip
    4.6 MB · Views: 464
[Guide] HP Envy Haswell series J/K using Clover UEFI (10.11)

blacktuxipl said:
Dear Tonymac86 Team :headbang:
Dear RehabMan

I have an issue patching my SSDT/DSDT.

./disassemle.sh runs without any problems.

But make patch get an error
make: *** No rule to make target `unpatched/.dsl', needed by `patched/.dsl'. Stop.
I have uploaded the files you probably need to help me with my problems.

Thanks patrick
Click to expand...

Make sure you boot with USB (prepared according to the guide) before running ./disassemble.sh.

Since you may have invalid files in ./unpatched, make sure you do 'make cleanallex' before running ./disassemble.sh.

It is important to follow the guide exactly as written.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top