2013 Mac Pro - My variation

[Bouly]

 

[jacknapster]

very cool. Is it possible to get Your stl-files (base, top and parts above)?

 

[Bouly]

very cool. Is it possible to get Your stl-files (base, top and parts above)?

Here the requested files.

Updating files in lower post.........​

 

[Bouly]

After 16 months of research and study, the mod is over.

The config :
☑ Gigabyte GA-Z87N-WIFI
☑ Intel Core i7-4770 3,4 GHz
☑ Thermalright AXP-100
☑ G.Skill Ares Série 16 Go (2 x 8 Go) de mémoire DDR3-1866
☑ MSI GeForce GTX 760 Gaming ITX
☑ Crucial M550 mSATA 256Go with msata to sata Half slim adapter
☑ HDD 2,5" WD Blue 1To 16Mo 7 mm
☑ Riser 3M PCI Express X16 L250mm
☑ Noctua NF-A15 PWM Fan 150mm
☑ Extension HDMI 90° 500mm
☑ Light button
☑ White Power Mac power cord

The case :
☑ A bathroom trash ''Authentics Lunar''
☑ Base, upper air diffuser, keeping Plates, motherboard support and SSD 3D printing
☑ Black anodized aluminum profile structure ‘'Makerbeam''


Mounting :

Support for the start button and the HDMI cord.

The power supply.

The lower support.

A part of structure.

PCI riser (after a full afternoon to bend), graphics card and power of it.

The motherboard support.

The Motherboard with the wiring.

Extension HDMI.

The motherboard equiped.

The mSATA drive and bracket.

The upper support.

The fan.

The upper air diffuser.

A small 360° with hard drive:

The case, the carrier and the closing ring.

The motherboard Cache (two working days).

The lower ring.

Ths closing.

Le case.

The cache up.

On the way ……….
​

 

[Dschijn]

Wow, really clean build!

 

[neilhart]

Bouly,

Thank you for sharing your photos. Very well done is an understatement.

I have scrolled up and down the photos several times to understand your project.

Good modding,
neil

 

[JuanLobo]

Very well done!

I like the 3d printed drive bracket, and I have always liked your top grill. I am tempted to print that and add it to mine.

Very clean cable routing!

The 25cm PCIe cable is tight, isn't it?

 

[JRDN]

Awesome Bouly, where did you get these printed at? I uploaded your stl files to shapeways and there's a few files that don't match what you have. Would you be able to upload your stl for the bottom base and the locking ring? I'm really interested in making a similar creation. What material choice did you go with? Here are what the previously attached files look like

 

[Bouly]

Awesome Bouly, where did you get these printed at? I uploaded your stl files to shapeways and there's a few files that don't match what you have. Would you be able to upload your stl for the bottom base and the locking ring? I'm really interested in making a similar creation. What material choice did you go with? Here are what the previously attached files look like

Hello,

I print my files at Shapeways , enclosed the requested files .

Latching on the ring , I used the bottom of the bin.

 

[JRDN]

Creative! Was the ring then glued to the inside to allow it to lock?
Thanks for the files. I looked at your 3d model mockup from the link below. What software did you use for your designs? There's tons of options for 3D Modeling it seems
http://www.tonymacx86.com/mac-pro-mods/123752-2013-mac-pro-my-variation-34.html#post860683