Contribute
Register

Can only boot in Safe Mode after update 10.10.3

Status
Not open for further replies.
Joined
Oct 3, 2014
Messages
155
Motherboard
ASUS Q500A (Clover)
CPU
i5 3210M/HM76
Graphics
HD 4000/1366x768
Mac
  1. 0
Classic Mac
  1. 0
Mobile Phone
  1. 0
On normal boot white Apple logo begins loading, when it is almost ready to load the system it restarts to Clover boot screen, only way getting to the OS is in safe mode, but graphics seem to work with lag and delay and the OS is really slow, any idea what is causing this? How can I fix this? At least it loads in safe mode so there's a chance we can fix this, help?
 
On normal boot white Apple logo begins loading, when it is almost ready to load the system it restarts to Clover boot screen, only way getting to the OS is in safe mode, but graphics seem to work with lag and delay and the OS is really slow, any idea what is causing this? How can I fix this? At least it loads in safe mode so there's a chance we can fix this, help?

What hardware?
 
What hardware?

ASUS Q500A with Clover r3193

Intel Core i5-3210M
Intel HD Graphics 4000
Chipset: Intel Ivy Bridge Rev: 9
SouthBridge: Intel HM76 Rev: 4

I got this info on screen if this helps

IMG_0417.jpg
 
On normal boot white Apple logo begins loading, when it is almost ready to load the system it restarts to Clover boot screen, only way getting to the OS is in safe mode, but graphics seem to work with lag and delay and the OS is really slow, any idea what is causing this? How can I fix this? At least it loads in safe mode so there's a chance we can fix this, help?

Not a desktop. Moved to laptop support.

May be graphics problem? http://www.tonymacx86.com/yosemite-...tel-hd4200-hd4400-hd4600-mobile-yosemite.html

Remove your network driver (looking now at verbose output your provided).
 
Not a desktop. Moved to laptop support.

May be graphics problem? http://www.tonymacx86.com/yosemite-...tel-hd4200-hd4400-hd4600-mobile-yosemite.html

Remove your network driver (looking now at verbose output your provided).

Where is the network driver located?

Also, In safe mode I can mount the EFI drive but cannot see the Clover EFI folder, so if I cannot install the fakeid kext into the Clover kext folder, what should I do? Install them in S/L/E ?



EDIT: Took some pictures of the system report in hopes this help you figure out whats wrong. Also I cannot copy the FAKEID kexts into OS X because it doesnt recognizes my USB pendrive, only recognizes if its formatted on OS X Journaled in disk utility, is this an issue of being in safe mode? I had no problems before? I beginning to feel frustration :banghead:

Report 1.jpgReport Page 2.jpg
 
Where is the network driver located?

It depends on where you installed it. (Clover/kexts or /S/L/E).

Also, In safe mode I can mount the EFI drive but cannot see the Clover EFI folder, so if I cannot install the fakeid kext into the Clover kext folder, what should I do? Install them in S/L/E ?

FAT/FAT32 partitions cannot be mounted in safe mode.
 
It depends on where you installed it. (Clover/kexts or /S/L/E).



FAT/FAT32 partitions cannot be mounted in safe mode.


Well Im ****ed then, cause I cannot see the EFI Clover folder were I copied the network kext, and neither access FAT/FAT32 partitions to copy the fakeid kext, no way I can fix this, will have to reinstall everything again...

:banghead:
 
Well Im ****ed then, cause I cannot see the EFI Clover folder were I copied the network kext, and neither access FAT/FAT32 partitions to copy the fakeid kext, no way I can fix this, will have to reinstall everything again...

:banghead:

You can access the EFI partition from Linux or Windows.
 
You can access the EFI partition from Linux or Windows.

How can I access it from Windows?

I ask because I just did a clean reinstall and I'm downloading the Combo Update, and downloaded the the FakeID kext etc, and will prepare a time machine backup just in case, I wanna update to 10.10.3 so I have to ask, since I'm using Clover, I have to install the FakePCIID kexts in EFI/Clover/Kext/Other and I have to also add the patch to the config.plist in order for it to work? I have Intel HD 4000 with device id 8086:0166, will the FakePCIID kext work for this?
 
How can I access it from Windows?

You have to mount it (eg. assign a drive letter) with diskpart.exe. And you'll need to do all mods from an elevated CMD.EXE prompt, or re-launch explorer.exe as Admin (eg. elevated).

I ask because I just did a clean reinstall and I'm downloading the Combo Update, and downloaded the the FakeID kext etc, and will prepare a time machine backup just in case, I wanna update to 10.10.3 so I have to ask, since I'm using Clover, I have to install the FakePCIID kexts in EFI/Clover/Kext/Other and I have to also add the patch to the config.plist in order for it to work? I have Intel HD 4000 with device id 8086:0166, will the FakePCIID kext work for this?

You should install all kexts you need to /S/L/E. Clover injection (EFI/Clover/kexts) should only be use when necessary (installer and recovery).

FakePCIID is not needed for HD4000. Device 8086:0166 is recognized natively.
 
Status
Not open for further replies.
Back
Top