Xeon E5 - 16 Cores/ 32 Thr Z9PE-D8 WS 16TB GeekBench 28,000
Paradigm99's Build: 2x Xeon E5 2680 - Asus Z9PE-D8 WS - XFX Radeon 6870Components
2x Xeon E5 2680
Asus Z9PE-D8 WS Motherboard
Case Labs STH10 Case
2x Corsair H100
Vertex 4 128GB SSD
Corsair AX1200 Power Supply
XFX Radeon 6870 2GB
Corsair Vengeance 32GB RAM (4x 8GB)
ASUS DRW-24B1ST/BLK/B/AS Black SATA 24X DVD Burner
SILVERSTONE SST-FP32-B Front I/O Panel
8x 120mm Case Fans
Apple OS X Lion @ Mac Apps Store
4x 3TB HDD (Seagate and Western Digital)
(Already owned) (Purchased from Costco as external drives and stripped to bear drive) $130 ea.!!!!
My build was slightly different than the conventional Hackintosh for a few reasons… Please keep this in mind when attempting this yourself (in other words don't follow these first few steps unless you own another Apple computer - not another Hackintosh)
After the "updated" Mac Pros were released in early June, I began to think about alternatives to handle my film and graphic intensive work load.
I did some research and found that my Mac Pro's config could be sold and fully if not almost fully offset the cost for my hackintosh build!
I spent about 2 weeks looking for all of the right parts, as I will not be needing to buy a new computer for a very long time as Apple's Mac pros will still not surpass my new builds power for at least another year and a half.
Thoughts on the build:
After I had received all the parts from Newegg and Amazon (check both because I got some really good deals on Amazon that were not on Newegg - ex. saved $60 on my Power supply!) I attached my vertex 4 SSD to a Seagate Go-flex portable hard drive adaptor cable (I use this for my Macbook Air time machine and bought from Costco - 1.5TB for 150 bucks!). I then copied the base OS from my Macbook air and everything required to boot. I then booted off of the SSD (still on my Macbook air) and installed the EASYBEAST tool from Multibeast. I then proceeded with the actual Hackintosh build.
I had used the Case labs STH10 case for the build (I wrote a review on the case -its by John)
- note my Mobo was SSI-EEB form factor (not officially supported by the STH10 however it is, and was confirmed when it fit =D). The case needed to be assembled which I enjoyed it took about 2 hours to complete (pay attention to the pictures if you build this case!) I then tested everything OUTSIDE THE CASE to make sure there were no problems with any of the components before I installed them in the case.
OSX Booted without a problem, and after some fine tweaking, ethernet, onboard audio Realtek 898, USB 2.0 etc works fine. Still haven't found a working USB 3.0 driver but haven't given it much time yet, as all my storage is internal =D.
Here are the kexts I used get get my system working:
Geekbench 64BIT scored at approx. 28,000 which is still great compared to my 8 Core 2.4Ghz 5,1 Mac Pro. http://browser.primatelabs.com/geekbench2/796405
I have the 4, 3TB HDDs in 2 Raid configs, both in Raid 0 with one as a backup. I chose not to use raid 10 because I still like the archive feature of a normal backup.
Cinebench Comes in at just under 20 PTS! Idle temps for the system are approx. 30 degrees C, and 39 degrees C UNDER FULL LOAD!!!! The system is not super loud, but it is still noisy… the is due to the cheap 120mm fans I bought for the case. As time goes by i'll upgrade the fans one at a time, so I'm not spending 150 bucks on case fans. In the future I think I will also get another set of RAM to utilize quad-channel supported by the XEON E5's.
A VERY GOOD thing to keep in mind is:
After your system is bootable, before you install extra kexts to get everything working (unless you use a DSDT) is to enable a screen sharing application. Either Logmein or the Mac version (both work fine). I had accidentally disabled by USB ports by improperly installing the next. Luckily I had screen sharing enabled for this very reason!
If anyone is thinking about building a super computer similar to this one, and has any questions, please feel free to ask!
As time goes on I will continue to post updates etc regarding this build.
A VERY BIG THANK YOU TO TONYMACX86 FOR IMPROVING MY PRODUCTIVITY BY 3X FOR THE SAME COST AS MY MAC PRO =D