Search results

Correct, I am working with a generic install just to try to solve these issues and learn. I have a solid install on another that I have added the serial number and have messages working. Of course booting with iGPU Disabled or in Auto. Of course at my knowledge level I may not understand how...

@macnb The post on a previous thread where you explained that you configured your own system gives an EFI for me to try, but I have not seen a list of the kexts you load. Your and my system are pretty much identical. Gigabyte GZ-Z77X-UP5-TH, i7-3770K, RX 580. I am booting from Samsung SSD...

Thanx macnb. Very interesting about APFS filling. I have included a screenshot of 'Get Info'. It is mainly empty. When I follow your steps to boot, it boots normally. The only time I have a problem is when MultiBeast has been run and the iGPU is enabled. I loaded the Mojave just fine with it on...

Thanx pastrychef. It's not that it won't. In fact during the last install I had it enabled and it showed both video cards after in the System Report. However, once I ran MultiBeast, it went back into the reboot loop. Meaning, about halfway through boot, it will reboot. Both from trying to boot...

THANK YOU!! New thread here: https://www.tonymacx86.com/threads/ga-z77x-up5-th-bios-video-settings-and-reboot-issue-rebootloop.267095/#post-1868928

I hope this in correct section, please advice if not. CONDENSED VERSION BETWEEN THE LINES BELOW First of all I would like to thank everyone who contributes to this site. Both with questions and with answers. I have been part since 2013. I believe Mountain Lion was the first OS I loaded on my...

Well Bummer. After MultiBeast install I went back into reboot loop with iGPU enabled in BIOS. I had to change it back to Auto to boot. I wonder if it is some sort of clover issue? Anyone with any thoughts? Booted fine and showed both Graphics Adapters in System Report before MultiBeast 11.0.1...

Thank You. Yes, I have done that previously. Here is where I am now. I tried setting iGPU to enable in BIOS and got a reboot loop. So I decided to chose another drive and start a fresh install to try a few things. I set iGPU back to Enabled, 512M, Max. Install went wonderfully and I show both...

Anybody watching? Solved the JPEG preview with NoVPAjpeg.kxt. Machine runs fine with iGPU set to Auto. When set to Enabled I get the reboot loop.

THANK YOU for your input :wave: I am going to try your suggestions. I have been running my iGPU set to Auto. I have wondered if there is a difference from Enabled. When I set it to Enabled, I get a reboot loop. It boots so far then reboots. The verbose text is so fast I cannot see what is...

I run a Asus RX580 and both screens light up during the Mojave install. I have both running right now with no configuration yet. I have yet to install even WhateverGreen. Not saying I won't. Just trying to figure out what advantage it gives. My RX 580 is reported properly in 'About' and is...

FIXED!!: I always like when a solution is posted, so I am letting everyone know it is solved and how. I must thank @RehabMan. He solved it indirectly. I began reading his FAQ on things to do before asking a question. I came to the part describing how to load kexts manually. I removed the...

FIXED!!: I always like when a solution is posted, so I am letting everyone know it is solved and how. I must thank @RehabMan. He solved it indirectly. I began reading his FAQ on things to do before asking a question. I came to the part describing how to load kexts manually. I removed the...

Thank You pastrychef. I am sorry for forgetting to include that. Yes, I did have them there as well. They did not load from there either. Then I had a response and read that as you say, they shouldn't be there so I used KextBeast and installed them in /L/E thinking surely that would work. I...

Thank You for your input! I have been :banghead: for two nights now on what seems to me should be a simple thing to do. I downloaded WEG and NoVPAJpeg. I copied them to /L/E and rebooted. No result. So I started digging. Everything I found says this is the proper procedure. I finally came to...

I have read on here to not use kextbeast because placing custom kexts into S/L/E is not desirable. I also am understanding some kexts like Lilu and WhateverGreen need to be in L/E due to being needed at boot time. Please, anyone jump in if I am incorrect. The silly problem I seem to be having...

Thank You, I am trying that. I am having a very strange problem with not being able to load the WhateverGreen and NoVPAJpeg kexts. I get a permission error. I changed ownership to root:wheel in L/E and tried them in EFI/EFI/COLVER/Kexts/Other. Very strange :/

Sleep mode was working fine when I installed. Once I start loading software for some reason it stops working. It has been the case on every build. I do not use a DSDT. I remember when I bought this board for the first install it said here that a DSDT was not required. I know when I had the...

I want to let you know I truly appreciate your post. I have also been 'Hackintoshing' along a GA-Z77x-UP5 TH since, if I remember correctly, Leopard. It has been challenging at times but when finally each time configured correctly, ROCK SOLID! I recently exchanged the GeForce GTX 680 for a ASUS...

Did you figure out the reboot issue? Did it fix the jpg issue? I have Z77X-UP5 TH with ASUS RX580. I also get the reboot when enabling IGPU. Hoping for a resolution.