Contribute
Register

[HELP ME!] MoBo: DH67CL + i5 (2500) + Graphics HD2000 + 8GB .

Status
Not open for further replies.
hasbrone

hasbrone

Joined
Nov 4, 2014
Messages
17
Motherboard
DH67CL + 10GB
CPU
Core i5 2500 @ 3.20GHz
Graphics
ASUS GT610
Mac
  1. Mac Pro
Classic Mac
  1. 0
Mobile Phone
  1. Android
Please!


I would install Mountain Lion on me: DH67CL (DH67XX MoBo)
Someone, Could give me the correct settings for the BIOS?.
In addition, to provide me "Flags" (Optional Boot Arguments, Eg. PCIRootUID=0) used for installation...


Thank You Very Much.
 
RehabMan said:
Read here: http://www.tonymacx86.com/mountain-...-dh67gd-core-i7-2600k-hd3000-ml-10-8-2-a.html

Please note: You'll need a graphics card (HD2000 is not supported).
Click to expand...
Yes, this is the guide that I am following.
I have some doubts with some parameters in the BIOS, I think that might affect the installation.


This is my configuration in the BIOS:
MAIN
BIOS Versión: BLH3710H.86A.0160.2012.1204.1156 (160)
Active Processor Cores: ALL
CONFIGURATION
Onboard Devices
Enhanced Consumer IR: Disable
Audio: Enable
Front Panel Audio: Disable
HDMI/DisplayPort Audio: Enable
LAN: Enable
Num Lock: On
PCI Latency Timer: 32
SATA Drivers
Chipset SATA: Enable
Chipset SATA Mode: AHCI
S.M.A.R.T.: Enable
SATA Port 0: ST500DM002-1BD (500.1GB-6.0Gb/s)
SATA Port 1: HL-DT-ST DVDRA (1.5Gb/s)
eSATA Ports: Disable
SATA Port X Hot Plug Capability: Disable
Hard Disk Pre-Delay: No
Event Log
Clear Event Log: No
Event Logging: Enable
Video
Integrated Graphics Device: Enable if Primary
IGD DVMT Memory: Maximum DVMT
Primary Video Adaptor: Auto
IGD Primary Video Port: Auto
No Video Detected Error Beeps: Disable
SECURITY
Chassis Intrusion: Log Only
Execute Disable Bit: Enable
Intel Virtualization Technology: Disable
POWER
Enhanced Intel SpeedStep Technology: Enable
Processor C States: Enable
After Power Failure: Stay Off
Wake on LAN from S4/S5: Power On - Normal Boot
S3 State Indicator: Blink
Wake System from S5: Disable
PCIe ASPM Support: Disable
Flash Update Sleep Delay: Disable
BOOT
Boot Menu Type: Advanced
Boot Drive Order: P0:ST500DM002-1BD142
Boot to Optical Devices: Disable
Boot to Removable Devices: Enable
Boot to Network: Disable
USB Boot: Enable
Boot USB Devices First: Disable
UEFI Boot: Enable
General Optimization: Disable
USB Optimization: Disable
Video Optimization: Disable


@RehabMan, Do you think?, There any parameter to be changed?
Thank You Very Much.
NOTE: thanks for the tip on the graphics card.
 
hasbrone said:
Yes, this is the guide that I am following.
I have some doubts with some parameters in the BIOS, I think that might affect the installation.

...
Click to expand...

Default BIOS settings + enable UEFI boot (even if you plan to boot legacy).

My guide is written for Chimera/Chameleon, but I'm currently using Clover.

Give it a try and see what happens...

Let me know if you need info on Clover config.
 
RehabMan said:
Default BIOS settings + enable UEFI boot (even if you plan to boot legacy).

My guide is written for Chimera/Chameleon, but I'm currently using Clover.

Give it a try and see what happens...

Let me know if you need info on Clover config.
Click to expand...
Sure!.
I would like to install using Clover, I can help? ...
Please and Thank You.
 
I would install Yosemite (10.10.1) with Clover in my DH67CL (just like you).
Can you help me?, Where do I start?...
 
hasbrone said:
Sure!.
I would like to install using Clover, I can help? ...
Please and Thank You.
Click to expand...

The only trick is power management during install. You need a special SSDT (for EFI/Clover/ACPI/patched/SSDT-1.aml). It supplies the missing Processor objects in Scope (_PR).

And you need a correct config.plist. I've attached the one I use for installs.

Note: My config is for onboard HD3000. You'll probably need to tweak the config your your nvidia.
 

Attachments

  • Clover-DH67xx.zip
    1.9 KB · Views: 137
RehabMan said:
The only trick is power management during install. You need a special SSDT (for EFI/Clover/ACPI/patched/SSDT-1.aml). It supplies the missing Processor objects in Scope (_PR).

And you need a correct config.plist. I've attached the one I use for installs.

Note: My config is for onboard HD3000. You'll probably need to tweak the config your your nvidia.
Click to expand...
Thank You Very Much.
The guide I have to follow is this: How To Install OS X Yosemite Using Clover, and use the trick for Power Management.
A Doubt: I need tweak only config.plist for my nVidia? o I need tweak also SSDT-1.aml?...
 
hasbrone said:
Thank You Very Much.
The guide I have to follow is this: How To Install OS X Yosemite Using Clover, and use the trick for Power Management.
A Doubt: I need tweak only config.plist for my nVidia? o I need tweak also SSDT-1.aml?...
Click to expand...

Just tweak config.plist. Because it is setup to inject properties/fakeid/etc for Intel HD3000 desktop. The SSDT-1.aml is just to solve a problem with how the Processor objects are declared in SSDT -- we drop the OEM SSDT so it doesn't bother -- and then provide a corrected one.

You probably have some research to do on the nvidia stuff (don't have any...), yours may just be natively supported though.
 
RehabMan said:
Just tweak config.plist. Because it is setup to inject properties/fakeid/etc for Intel HD3000 desktop. The SSDT-1.aml is just to solve a problem with how the Processor objects are declared in SSDT -- we drop the OEM SSDT so it doesn't bother -- and then provide a corrected one.

You probably have some research to do on the nvidia stuff (don't have any...), yours may just be natively supported though.
Click to expand...
I also think that maybe supported natively, because I made an installation of Mavericks (in a DH55HC) with this graphics card (GT610) without problem.

Thanks for the help.
This morning at work I'll try and speak of what happens.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top