Help with HDMI AUDIO (Yosemite - i5 4690k - GA-Z97N-WIFI - Intel HD 4600)

Hi,

I can't enable audio over HDMI.

I've tried the following guides:
1- [Guide]_HD4600-hdmi_audio_(dsdt_or_ssdt)_v2.1.3
2- [Guide]_OS_X_hdmi_audio-dsdt_v2.1

I do not what else to do.

Thanks!

Alberich99 said:

I do not what else to do.

Click to expand...

The only correct file is the edited dsdt and that is not installed, install.
An ssdt is installed, not attached, not from this site, remove.
Config.plist is a mess, start over.
Fresh config.plist:
1. ACPI/DSDT/Fixes/NO (all or remove)
2. ACPI/DSDT/Patches/remove
Run audio_cloverALC... (answer HD46000 HDMI audio? y)
Restart.
HD46000 HDMI audio will not work (without Azul patches).
Attach all requested files.

I think it's easier if I just restore from the bootable backup.

This is what I'm going to do:

1. I start here: http://www.tonymacx86.com/hdmi-audio/143760-audio-hdmi-audio-applehda-guide.html (for ease, the "Forum Guide").
2. From the first table, Row 8 applies, so I download the guide from row 7, column 2 (HD4600-hdmi_audio, which downloads "[Guide]_HD4600-hdmi_audio_(dsdt_or_ssdt)_v2.1.3.pdf" (for ease, the "PDF Guide 1")
3. I try to download the files from the link in row 8, column 3 but I get a "400: invalid request" error. (Should I try the link in row 8, column 4?)
4. I take note of row 8, column 5 and the applicable Kext edit is Azul.
5. I downloaded all the tools.
6. I added the source to MaciASL.

After this, things get messy.
7. Should I continue from the Forum Guide or from the PDF Guide 1?
8. I decided to continue from the Forum Guide.
9. From the table "Clover/kext edits (config.plist)", I choose the links in row yosemite, column 2 and row yosemite, column 5 ​(Both links point to the same file, right?)
10. Here I get confused again, I copy/paste what's in the KextToPatch section of the downloaded plist file to the KextToPatch of the plist in EFI/CLOVER and save the file? can I use TextEdit?

11. The Forum Guide ends here, since Part C is not applicable, right? So I reboot here?

Thanks for your help!

Alberich99 said:

This is what I'm going to do:

Click to expand...

The url connects MaciASL to the correct edit repo, no downloads.
Use a plist editor, not TextEdit.
Attach the edited dsdt and config.plist

OK, I'm attaching the DSDT and the new config.plist (which is already in the EFI folder of the EFI partition.

Should I now copy the DSDT file to EFI/EFI/CLOVER/ACPI/patched folder and restart? Am I missing something?

Thanks,

Alberich99 said:

Should I now copy the DSDT file to EFI/EFI/CLOVER/ACPI/patched folder and restart? Am I missing something?

Click to expand...

Edited dsdt is correct, install. Ignored all config.plist suggestions, will not work. Try again.

I copied/pasted the DSDT to the patched folder.

I'm attaching config.plist again. I copied/pasted from "config-hdmi_hd4600-100.plist" (note I didn't deleted nor replaced anything from original "config.plist", just pasted). I'm attaching my original "config.plist" for reference.

Is this ok?

Alberich99 said:

Is this ok?

Click to expand...

No. Big "paste" problems, worse.
KestsToPatch/Find and Find2, Name and Name 2, etc.
Start over with a new config.plist
Paste only the config-hdmi_hd4600-100.plist/patches that guide says to copy. Several to not apply to your system.

toleda said:

No. Big "paste" problems, worse.

Click to expand...

I'm attaching a new one. I pasted as child just one (azul for port 0x5).

if this is correct, what now?

Alberich99 said:

if this is correct, what now?

Click to expand...

3rd request, start over. A clean config.plist has no #.
Ignored Post #2 again
Voodoo disables AppleHDA. AppleHDAController patch not correct. Two required patches missing.